Instrukcja obsługi AXESS AXDIS-GMLN44

AXESS Niesklasyfikowane AXDIS-GMLN44

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AXESS AXDIS-GMLN44 (12 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
AXDIS-GMLN44
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 5/4/20 INSTAXDIS-GMLN44
INTERFACE FEATURES
INTERFACE COMPONENTS
TABLE OF CONTENTS
Connections to be made ................................... 3-6
- For models
without
an amplifier .......................3
- For models
with
an analog amplifier ................4
- For models
with
a digital amplifier ...................5
- 3.5mm jack steering wheel control retention ..6
Installing the AXDIS-GMLN44 ................................6
Programming the AXDIS-GMLN44 ........................7
Adjusting the AXDIS-GMLN44 ...............................7
Steering wheel control settings ......................8-10
- L.E.D. feedback ....................................................8
- Changing radio type ...........................................8
- Remapping the steering wheel control buttons ..9
- Dual assignment instructions
(long button press) ............................................ 10
Troubleshooting .................................................... 11
GM Data Interface with SWC 2012-2016
• Provides accessory power
(12-volt 10-amp)
• Retains R.A.P. (retained
accessory power)
• Provides NAV outputs (parking
brake, reverse, speed sense)
• Retains chimes
• Retains audio controls on the
steering wheel
• Retains OnStar / OE Bluetooth
• Adjustable OnStar level
• Retains the factory AUX-IN jack
•
Can be used in non-amplified, or
analog/digital amplified models
• Retains balance and fade
(excluding digital amplified
models)
• Micro “B” USB updatable
• AXDIS-GMLN44 interface • AXDIS-GMLN44 harness
• 16-pin harness with stripped leads • 4-pin to 4-pin resistor pad harness
• Female 3.5mm connector with stripped leads
APPLICATIONS
See inside front cover
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape • Connectors (example: butt-connectors, bell caps, etc.) • Small flat-blade screwdriver
2
APPLICATIONS
CHEVROLET
Avalanche † * 2012-2013
Express † 2013-2015
Malibu (with monochrome display) 2013-2015
Malibu Limited (with monochrome display) 2016-2016
Silverado 2500 / 3500 † * 2014
CHEVROLET (CONT)
Silverado † * 2012-2013
Suburban † ** 2012-2014
Tahoe † ** 2012-2014
Trax 2015-2016
GMC
Savana † 2013-2015
Sierra 2500 / 3500 † * 2014
Sierra † * 2012-2013
Yukon / Yukon XL † ** 2012-2014
* These vehicles have a digital amp option. Please reference the “Service Parts Identification” sticker located in the glove box for the RPO code Y91. If Y91 is present, then the vehicle is equipped with
a digital amplifier.
** These vehicles have a digital amp option. Please reference the “Service Parts Identification” sticker located in the glove box for the RPO codes; Y91, STZ, UQS. If Y91, STZ or UQS is present, then the
vehicle is equipped with a digital amplifier.
† Only for models with NAV.
3
REV. 5/4/2020 INSTAXDIS-GMLN44
CONNECTIONS TO BE MADE
Attention!
This interface will work with models that are either non-amplified, analog amplified, or
digital amplified. Please follow the instructions carefully for your model vehicle. Failure to do so
will result in either no sound, or low sound. If you are unsure if your vehicle is factory amplified or
not, please contact your local dealership.
For models
without
an amplifier:
From the 16-pin harness with stripped leads to the aftermarket radio:
• Connect the wire to the accessory wire.Red
• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
• If the aftermarket radio has a mute wire, connect the Brown wire to it. If the mute wire is
not connected, the radio will turn off when OnStar is activated.
• Connect the wire to the right front positive speaker output.Gray
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the wire to the left front positive speaker output.White
• Connect the wire to the left front negative speaker output.White/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
• Connect the wire to the VSS/speed sense wire.Blue/Pink
• Connect the wire to the reverse wire.Green/Purple
• Connect the Light Green wire to the parking brake wire
• Tape off and disregard the following (5) wires, they will not be used in this application:
Blue/White Green Green/Black Purple Purple/Black, , , and .
From the AXDIS-GMLN44 harness to the aftermarket radio:
• Connect the wire to the ground wire.Black
• Connect the Yellow wire to the battery wire.
• Cut off the resistors from the , Green Green/Black Purple Purple/Black, , and wires below the
heat shrink.
• Connect the wire to the left rear positive speaker output.Green
• Connect the wire to the left rear negative speaker output.Green/Black
• Connect the wire to the right rear positive speaker output.Purple
• Connect the wire to the right rear negative speaker output.Purple/Black
• Ensure the (2) 4-pin Molex connectors are connected together.
Note:
The 4-pin to 4-pin resistor pad harness will not be used in this application.
•
The Black/Yellow wire is used for OnStar level adjustment for models that do not come equipped
with steering wheel controls. Refer to the OnStar level Adjustment section for further instructions
.
• Disregard the wire with a red bullet connector, it will not be used in this application.Pink
• Connect the and RCA jacks to the audio AUX-IN jacks of the aftermarket radio.Red White
• Disregard the DIN jack and wire.Red
Note:
The relay attached to the AXDIS-GMLN44 harness is only for audible turn signal clicks.
No extra steps are required to retain this feature, so leave the relay as-is.
Continue to 3.5mm jack steering wheel control retention

Specyfikacje produktu

Marka: AXESS
Kategoria: Niesklasyfikowane
Model: AXDIS-GMLN44

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AXESS AXDIS-GMLN44, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane AXESS

AXESS

AXESS AXBUCS-MZ286V Instrukcja

9 Października 2024
AXESS

AXESS 99-7014HG Instrukcja

8 Października 2024
AXESS

AXESS AXGM-17 Instrukcja

8 Października 2024
AXESS

AXESS AXGMLN-34 Instrukcja

8 Października 2024
AXESS

AXESS 99-7382HG Instrukcja

8 Października 2024
AXESS

AXESS GMOS-12 Instrukcja

8 Października 2024
AXESS

AXESS XSVI-1788-NAV Instrukcja

8 Października 2024
AXESS

AXESS 99-7510HG Instrukcja

8 Października 2024
AXESS

AXESS AXBUCS-NI246V Instrukcja

8 Października 2024
AXESS

AXESS 99-3307G Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024