Instrukcja obsługi AXESS AX-FT901

AXESS Niesklasyfikowane AX-FT901

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AXESS AX-FT901 (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-FT901

I N S TA L L A T I O N I N S T R U C T I O N S

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.)

TABLE OF CONTENTS

Connections to be made ....................................2-3

Installing the AX-FT901 interface ..........................3

Programming the ASWC-1 interface ................. 3-4

Screen operation ................................................4-6

Fiat 500 500L 2015 / 2014 (with U-Connect) Data Interface with SWC & Factory Display Retention †

• Provides accessory power

• Designed for non-ampliﬁed models

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains balance and fade

• Retains most of the vehicle settings that was displayed on the

factory radio *

• Micro “B” USB updatable

† For Continental Mopar head unit

* Attention!

The aftermarket radios backup camera input will be used to display the vehicle settings. If the radio doesn’t have a backup camera

Input, then there will be no visualization of the vehicle settings. An externally mounted screen could be substituted in this situation.

• AX-FT901 interface

• ASWC-1 interface

• AX-FT901 harness

• ASWC-1 harness

CONNECTIONS TO BE MADE

From the aftermarket radio to the AX-FT901 harness:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• Connect the wire to the accessory wire.Red

• If the aftermarket radio has an illumination wire, connect the wire to it.Orange

• Connect the wire to the power antenna turn-on wire.Blue

• Connect the wire to the left front positive speaker wire.White

• Connect the wire to the left front negative speaker wire.White/Black

• Connect the wire to the right front positive speaker wire.Gray

• Connect the Gray/Black wire to the right front negative speaker wire.

• Connect the wire to the left rear positive speaker wire.Green

• Connect the wire to the left rear negative speaker wire.Green/Black

• Connect the wire to the right rear positive speaker wire.Purple

• Connect the wire to the right rear negative speaker wire.Purple/Black

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the wire to the parking brake wire.Light Green

From the aftermarket radio to the ASWC-1 harness:

This harness is only to be used if the vehicle is equipped with steering wheel controls or a backup camera.

• Connect the wire to the accessory wire.Red

• For the radios listed below, connect the

female 3.5mm connector with stripped leads

, to

the

male 3.5mm SWC jack from the ASWC-1 harness. Any remaining wires tape off and disregard

• Connect the steering wheel control wire, normally Eclipse: Brown Brown/, to the

White wire of the connector. Then connect the remaining steering wheel control wire,

normally , to the wire of the connector.Brown/White Brown

• Connect the steering wheel control Key 1 wire (Gray) to the wire.Metra OE: Brown

• Kenwood or select JVC with a steering wheel control wire: Blue/Yellow Connect the

wire to the wire.Brown

• XITE:

Connect the steering wheel control SWC-2 wire from the radio to the Brown wire

•

Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold

separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio

Note:

The radio must be updated to rev. 2.1.4 or higher software.

•

Universal “2 or 3 wire” radio:

Connect the steering wheel control wire, referred to as

Key-A or SWC-1, to the

Brown

wire of the connector. Then connect the remaining

steering wheel control wire, referred to as Key-B or SWC-2, to the

Brown/White

wire of

the connector. If the radio comes with a third wire for ground, disregard this wire.

Note:

After the interface has been programmed to the vehicle, refer to the manual

provided with the radio for assigning the SWC buttons. Contact the radio manufacturer

for more information.

Continued on the next page

REV. 5/10/2018 INSTAX-FT901

• For all other radios: Connect the 3.5mm jack from the ASWC-1 harness, into the jack on the

aftermarket radio designated for an external steering wheel control interface. Please refer to

the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.

• Connect the Yellow male RCA jack labeled “To Reverse Camera Input (Radio)”, to the backup

camera input.

Note:

The aftermarket radios backup camera input will be used to display the vehicle

settings. If the radio doesn’t have a backup camera Input, then there will be no visualization

of the vehicle settings. An externally mounted screen could be substituted in this situation.

• If installing an aftermarket backup camera, connect the Yellow female RCA jack labeled “To

Reverse Camera”, to the camera.

With the key in the off position:

• Connect the AX-FT901 harness to the AX-FT901 interface, and then to the wiring harness in

the vehicle.

• Connect the ASWC-1 harness to the ASWC-1 interface, and then to the AX-FT901 interface.

• Press and hold the Volume-Up button on the steering wheel.

• Turn the ignition on, the L.E.D. in the ASWC-1 interface will start ﬂashing rapidly, which

means the ASWC-1 is looking for the vehicle and the radio.

Note:

If the L.E.D. did not start ﬂashing rapidly, press the reset button for 3 seconds, while

still holding the Volume-Up button.

• After a few seconds the L.E.D. should stop ﬂashing rapidly, and then go out for

approximately 2 seconds.

• After approximately 2 seconds there will be a series of 7 Green ﬂashes, some short, and

some long. The long ﬂashes represent the wires that are connected to the ASWC-1. The 3rd,

4th, 5th, and 6th ﬂashes should be longer.

Tip:

Knowing this will help to troubleshoot, if need be.

• The L.E.D. will pause for another 2 seconds, and then ﬂash up to 18 times depending on Red

which radio is connected to the ASWC-1. Refer to the L.E.D. feedback section for information.

• This is the end of the auto detection stage. Release from holding the Volume-Up button.

If the ASWC-1 detected the vehicle and the radio successfully, the L.E.D. will light up solid.

• Test the steering wheel controls for proper operation. Refer to the ASWC-1 instructions online

at axxessinterfaces.com for customizing the buttons, if so desired.

CONNECTIONS TO BE MADE (CONT.)

INSTALLING THE AX-FT901 INTERFACE

PROGRAMMING THE ASWC-1 INTERFACE

Continued on the next page

Specyfikacje produktu

Marka:	AXESS
Kategoria:	Niesklasyfikowane
Model:	AX-FT901

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AXESS AX-FT901, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane AXESS

AXESS AXBUCS-MZ286V Instrukcja

9 Października 2024

AXESS 99-7014HG Instrukcja

8 Października 2024

AXESS AXGM-17 Instrukcja

8 Października 2024

AXESS AXGMLN-34 Instrukcja

8 Października 2024

AXESS 99-7382HG Instrukcja

8 Października 2024

AXESS GMOS-12 Instrukcja

8 Października 2024

AXESS XSVI-1788-NAV Instrukcja

8 Października 2024

AXESS 99-7510HG Instrukcja

8 Października 2024

AXESS AXBUCS-NI246V Instrukcja

8 Października 2024

AXESS 99-3307G Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024