Instrukcja obsługi AXESS AX-ADGM04

AXESS Niesklasyfikowane AX-ADGM04

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AXESS AX-ADGM04 (12 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
AX-ADGM04
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 5/4/20 INSTAX-ADGM04
INTRODUCTION
INTERFACE FEATURES
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun, solder,
and heat shrink • Small flat-blade screwdriver
• Tape
• Wire cutter • Zip ties
TABLE OF CONTENTS
Connections to be made
For models
without
an amplifier .......................3
For models
with
an analog amplifier ................4
For models
with
a digital amplifier ...................5
12-pin pre-wired ASWC-1 harness ......................6
DIN jack ................................................................6
Installing & programming the AX-ADGM04
AX-ADBOX1 ...........................................................6
AX-ADBOX2 .......................................................... 7
Adjusting the AX-ADGM04 ....................................8
Extra features .........................................................9
GM Data Interface 2012-2016
APPLICATIONS
See inside front cover
The AX-ADGM04 harness is designed for, and must be used with, the
AX-ADBOX1 or AX-ADBOX2 interface (sold separately). Please refer to the
AX-ADBOX1 or AX-ADBOX2 for the 16-pin connector with stripped leads
.
• Provides accessory power (12-volt 10-amp)
• Maintains the retained accessory power
(R.A.P.) feature
• Provides NAV outputs (parking brake,
reverse, speed sense)
• Retains chimes
• Retains OnStar / OE Bluetooth
• Adjustable OnStar level
• Retains RSE (rear seat entertainment)
• Retains satellite radio
• Retains the factory AUX-IN jack
• Pre-wired ASWC-1 harness
(ASWC-1 sold separately)
• Can be used in non-amplified, or analog/
digital amplified models
• Retains balance and fade†
• Micro-B USB updatable
INTERFACE COMPONENTS
• AX-ADGM04 harness
• 4-pin to 4-pin resistor pad harness
† To retain fade in digital amplified models, use the AX-ADBOX1
2
APPLICATIONS
CHEVROLET
Avalanche † * 2012-2013
Express † 2013-2015
Malibu
(with monochrome display) 2013-2015
Malibu Limited
(with monochrome display) 2016
CHEVROLET (CONT)
Silverado 2500 / 3500 † * 2014
Silverado † * 2012-2013
Suburban † ** 2012-2014
Tahoe † ** 2012-2014
Trax 2015-2016
GMC
Savana † 2013-2015
Sierra 2500 / 3500 † * 2014
Sierra † * 2012-2013
Yukon / Yukon XL † ** 2012-2014
*
These vehicles have a digital amp option. Please reference the “Service Parts Identification” sticker located in the glove box for the RPO code Y91. If Y91 is present, then the vehicle is equipped with a digital amplifier
.
**
These vehicles have a digital amp option. Please reference the “Service Parts Identification” sticker located in the glove box for the RPO code Y91, STZ, or UQS. If Y91, STZ, or UQS is present, then the vehicle is equipped with a
digital amplifier
.
† Only for models equipped with NAV. If not equipped with NAV, use the AX-ADGM01.
3
REV. 5/4/2020 INSTAX-ADGM04
From the AX-ADGM04 harness to the aftermarket radio:
• Connect the wire to the ground wire.Black
• Connect the Yellow wire to the battery wire.
• If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) wires to Red
accessory power.
• Cut off the resistors from the Green Green/Black Purple Purple/Black, , , and wires below the
heat shrink.
• Connect the wire to the left rear positive speaker output.Green
• Connect the wire to the left rear negative speaker output.Green/Black
• Connect the wire to the right rear positive speaker output.Purple
• Connect the wire to the right rear negative speaker output.Purple/Black
• Ensure the (2) 4-pin Molex connectors are connected together.
Note: The 4-pin to 4-pin resistor pad harness will not be used in this application.
• The Black/Yellow wire is used for OnStar level adjustment for models that do not come
equipped with steering wheel controls. Refer to the OnStar level Adjustment section for
further instructions.
• Connect the and RCA jacks to the audio AUX-IN jacks from the aftermarket radio.Red White
• Disregard the wire with a red connector, it will not be used in this application.Pink
Note: The relay attached to the AX-ADGM04 harness is only for audible turn signal clicks.
No extra steps are required to retain this feature, so leave the relay as-is.
Continue to 12-pin pre-wired ASWC-1 harness
CONNECTIONS TO BE MADE
Attention! This interface will work with models that are either non-amplified, analog amplified,
or digital amplified. Please follow the instructions carefully for your model vehicle. Failure to
do so will result in either no sound, or low sound. If you are unsure if your vehicle is factory
amplified or not, please contact your local dealership.
For models
without
an amplifier:
From the 16-pin harness with stripped leads to the aftermarket radio (harness included with interface):
• Connect the wire to the accessory wire.Red
Note: If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) Red
wires on the AX-ADGM04 harness as well.
• Connect the wire to the power antenna wire.Blue/White
• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
• If the aftermarket radio has a mute wire, connect the wire to it. If the mute wire is Brown
not connected, the radio will turn off when OnStar is activated.
• Connect the wire to the right front positive speaker output.Gray
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the wire to the left front positive speaker output.White
• Connect the wire to the left front negative speaker output.White/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
• Connect the wire to the VSS/speed sense wire.Blue/Pink
• Connect the wire to the reverse wire.Green/Purple
• Connect the wire to the parking brake wireLight Green
• Tape off and disregard the following (4) wires, they will not be used in this application:
Green Green/Black Purple Purple/Black, , ,

Specyfikacje produktu

Marka: AXESS
Kategoria: Niesklasyfikowane
Model: AX-ADGM04

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AXESS AX-ADGM04, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane AXESS

AXESS

AXESS AXBUCS-MZ286V Instrukcja

9 Października 2024
AXESS

AXESS 99-7014HG Instrukcja

8 Października 2024
AXESS

AXESS AXGM-17 Instrukcja

8 Października 2024
AXESS

AXESS AXGMLN-34 Instrukcja

8 Października 2024
AXESS

AXESS 99-7382HG Instrukcja

8 Października 2024
AXESS

AXESS GMOS-12 Instrukcja

8 Października 2024
AXESS

AXESS XSVI-1788-NAV Instrukcja

8 Października 2024
AXESS

AXESS 99-7510HG Instrukcja

8 Października 2024
AXESS

AXESS AXBUCS-NI246V Instrukcja

8 Października 2024
AXESS

AXESS 99-3307G Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024