Instrukcja obsługi AXESS AX-ADDCAM

AXESS Niesklasyfikowane AX-ADDCAM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AXESS AX-ADDCAM (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-ADDCAM

I N S TA L L A T I O N I N S T R U C T I O N S

INTERFACE FEATURES

TOOLS REQUIRED

INTERFACE COMPONENTS

TABLE OF CONTENTS

Introduction............................................................2

Connections to be made .......................................2

Conﬁguring the AX-ADDCAM ............................. 3-5

Installing the AX-ADDCAM .....................................5

Programming the AX-ADDCAM .............................6

Connector pin-out (20-pin) ..................................7

AX-ADDCAM

• (4) Camera inputs

• Programmable 12V 5-amp switched output (conﬁgured through the Axxess Updater program)

• Reverse signal trigger generated via CAN bus communication of the vehicle

• Turn signal trigger generated via CAN bus communication of the vehicle

• (4) Programmable camera control wires (conﬁgured through the Axxess Updater program)

• Can also be manually controlled, and used along with an aftermarket radio

• VSS (Vehicle Speed Sense) input and output

• Micro “B” USB updatable

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell caps, etc.)

• AX-ADDCAM interface

• AX-ADDCAM harness

INTRODUCTION CONNECTIONS TO BE MADE

The Axxess AX-ADDCAM interface is a camera switching interface that will provide up to (3)

additional camera inputs to the factory radio, while still retaining the factory camera. With this

interface a front camera, and also side cameras can be added to the factory radio. The cameras

function automatically*, no human interaction required, unless desired to do so. Axxess has also

created a line of vehicle speciﬁc “Plug & Play” harnesses for the AX-ADDCAM. These harnesses must

be used along with the AX-ADDCAM. The AX-ADDCAM can also be used if the factory system does

not originally come equipped with a backup camera, adding up to (4) cameras in this instance. In

addition, the AX-ADDCAM can be used along with an aftermarket radio as well. Pending that the

aftermarket radio has an input designated for a backup camera

* Only applicable vehicles listed in the drop down menu in the Axxess Updater program will

retain this feature.

Note:

Some vehicles may not have the turn signal, and/or reverse signal available on the vehicles

CAN-bus. For vehicles that do not have those signals available, or when an aftermarket radio will be

used instead of the factory radio, the interface will need to be manually controlled by analog triggers.

12-volt switched output

The wire labeled “Camera 12V” will be used in applications where a 12-volt switched Red

output is required. In the Axxess Updater there are two options for this feature, “CAN

Detection”, or “Camera Active”. If an aftermarket radio will be used instead of a factory radio,

this wire must be connected to the wire designated for a reverse trigger

• Will provide a 12-volt switched output when the interface detects a CAN bus Accessory Out:

signal. Pending that the vehicle is supported under vehicle selection.

• Camera Active: Will provide a 12-volt switched output if a camera has been activated.

Camera input/output

The RCA jacks labeled “Camera 1 – 4” are the camera inputs. The RCA jack labeled “Camera

output” will go to the factory radio (or aftermarket radio). Camera 1 should only be used for a

backup camera as it takes priority over the other cameras. Camera 2 and 3 can be used for either

a left side camera, or a right side camera, as they are programmable within the Axxess Updater

program. Camera 4 is only for use with a front camera due to how the camera switching functions.

Analog control wires

(available with the “Plug & Play” harness)

There are (4) control wires for activating the cameras manually. The control wires can be

conﬁgured in the Axxess Updater for either a negative or positive trigger. The control wires can

also be assigned to any camera

VSS (vehicle speed sense)

(available with the “Plug & Play” harness)

The AX-ADDCAM will generate a VSS signal for applicable vehicles listed in the drop down menu in

the Axxess Updater. Pending that the vehicles CAN bus has that signal available. For vehicles that

do not have that signal available, the VSS wire will need to be manually wired to the vehicle. But

only if that feature is required.

• Blue/Green - VSS in.

• - VSS out.Green/Blue

REV. 5/3/2018 INSTAX-ADDCAM

CONFIGURING THE AX-ADDCAM

Continued on the next page

• Download and install the Axxess Updater program available at: axxessinterfaces.com

• Open the Axxess Updater and wait until the word “Ready” is listed in the bottom left of the screen.

• Select “Add-Cam Conﬁguration.

• Select the vehicle in the drop down list. If the vehicle is applicable, a tab labeled

“Conﬁguration” will appear.

•

Under “Make” and “Model”, there will be an option labeled “Other (Generic)”. This option is for

aftermarket radio installations where the AX-ADDCAM will be controlled via analog triggers

Specyfikacje produktu

Marka:	AXESS
Kategoria:	Niesklasyfikowane
Model:	AX-ADDCAM

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AXESS AX-ADDCAM, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane AXESS

AXESS AXBUCS-MZ286V Instrukcja

9 Października 2024

AXESS 99-7014HG Instrukcja

8 Października 2024

AXESS AXGM-17 Instrukcja

8 Października 2024

AXESS AXGMLN-34 Instrukcja

8 Października 2024

AXESS 99-7382HG Instrukcja

8 Października 2024

AXESS GMOS-12 Instrukcja

8 Października 2024

AXESS XSVI-1788-NAV Instrukcja

8 Października 2024

AXESS 99-7510HG Instrukcja

8 Października 2024

AXESS AXBUCS-NI246V Instrukcja

8 Października 2024

AXESS 99-3307G Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024