Instrukcja obsługi AXESS AX-ADCH03

AXESS Niesklasyfikowane AX-ADCH03

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AXESS AX-ADCH03 (16 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/16

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-ADCH03

I N S TA L L A T I O N I N S T R U C T I O N S

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun, solder,

and heat shrink • Small ﬂat-blade screwdriver

• Tape • Wire cutter • Zip ties

TABLE OF CONTENTS

Connections to be made

For models

without

an ampliﬁer .......................3

For models

with

an ampliﬁer ............................4

Installing & programming the AX-ADCH03

AX-ADBOX1 ...........................................................5

AX-ADBOX2 ..........................................................6

Adjusting the AX-ADCH03 .....................................7

Chrysler Data Interface 2013-up*

APPLICATIONS

See inside front cover

• Provides accessory power (12-volt 10-amp)

• Maintains the retained accessory power (R.A.P.) feature

• Can be used in non-ampliﬁed, or ampliﬁed models

• Provides NAV outputs (parking brake, reverse, speed sense)

• Pre-wired ASWC-1 harness (ASWC-1 sold separately)

• Retains the factory backup camera†

• Retains the factory AUX-IN jack

• Retains balance and fade*

• Micro “B” USB updatable

• AX-ADCH03 harness

*Visit AxxessInterfaces.com for up-to-date vehicle speciﬁc applications.

INTRODUCTION

The AX-ADCH03 harness is designed for, and must be used with, the

AX-ADBOX1 or AX-ADBOX2 interface (sold separately). Please refer to the

AX-ADBOX1 or AX-ADBOX2 for the 16-pin connector with stripped leads.

† Only if the camera is displayed on the factory radio

* To retain fade in ampliﬁed models, use the AX-ADBOX1

APPLICATIONS

CHRYSLER

200 LX 2015-2016

DODGE

Dart (small screen option) 2013-2016

JEEP

Cherokee (Sport trim) 2014-2017

Compass (Sport trim) 2017.5-up

RAM

1500/2500/3500

(small screen option) 2013-2017

Chassis Cab 3500, 4500, 5500

(small screen option) 2013-2017

REV. 9/24/2018 INSTAX-ADCH03

From the AX-ADCH03 harness to the aftermarket radio:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• If installing an ASWC-1 (sold separately), connect the wire to accessory power.Red

• Connect the wire to the right front positive speaker output.Gray

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the wire to the left front positive speaker output.White

• Connect the wire to the left front negative speaker output.White/Black

• Tape off and disregard the following (1) wire, it will not be used in this application:

Blue/White labeled “500L amp turn on”.

• If the vehicle is equipped with a factory backup camera, connect the Yellow RCA jack to a

jack on the aftermarket radio designated for a backup camera.

• If retaining the factory AUX-IN jack is desired, connect the and RCA jacks to the Red White

audio AUX-IN jacks from the aftermarket radio.

12-pin pre-wired ASWC-1 harness:

This harness is to be used along with the optional ASWC-1 (sold separately) to retain steering

wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If the ASWC-1

will be used, please refer to the ASWC-1 instructions for radio connections and programming.

Disregard the harness that comes with the ASWC-1.

Continue to Installing & Programming the AX-ADCH03

CONNECTIONS TO BE MADE

Attention! This interface will work with models that are either non-ampliﬁed, or ampliﬁed.

Please follow the instructions carefully for your model vehicle. Failure to do so will result in

either no sound, or low sound. If you are unsure if your vehicle is factory ampliﬁed or not, please

contact your local dealership.

For models

without

an ampliﬁer:

From the 16-pin harness with stripped leads to the aftermarket radio (harness included with interface):

• Connect the wire to the accessory wire.Red

If installing an ASWC-1 (sold separately), connect the wire on the AX-ADCH03 Note: Red

harness as well.

• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.

Attention! The following (4) wires are reversed on purpose. These wires will not match “color

code” to the aftermarket radio.

• Connect the wire to the right rear positive speaker output.Gray

• Connect the Gray/Black wire to the right rear negative speaker output.

• Connect the wire to the left rear positive speaker output.White

• Connect the wire to the left rear negative speaker output.White/Black

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the wire to the parking brake wireLight Green

• Tape off and disregard the following (6) wires, they will not be used in this application:

Blue/White Brown Green Green/Black Purple Purple/Black, , , , ,

Specyfikacje produktu

Marka:	AXESS
Kategoria:	Niesklasyfikowane
Model:	AX-ADCH03

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AXESS AX-ADCH03, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane AXESS

AXESS AXBUCS-MZ286V Instrukcja

9 Października 2024

AXESS 99-7014HG Instrukcja

8 Października 2024

AXESS AXGM-17 Instrukcja

8 Października 2024

AXESS AXGMLN-34 Instrukcja

8 Października 2024

AXESS 99-7382HG Instrukcja

8 Października 2024

AXESS GMOS-12 Instrukcja

8 Października 2024

AXESS XSVI-1788-NAV Instrukcja

8 Października 2024

AXESS 99-7510HG Instrukcja

8 Października 2024

AXESS AXBUCS-NI246V Instrukcja

8 Października 2024

AXESS 99-3307G Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024