Instrukcja obsługi AudioControl ACX-600.1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AudioControl ACX-600.1 (13 stron) w kategorii Receiver. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/13
COMPACT HIGH POWER ALL-WEATHER MONO AMPLIFIER
Quick Start Guide
Features
Compact High Power Mono Subwoofer Amplifier
High Current Design
1x 350 watts @ 4 Ohms
1 x 600 Watts @ 2 Ohms
12 dB/Octave Linkwitz-Riley Alignment Crossover
GTO™ Signal Sense (Great Turn On)
2 RCA Inputs - switchable for Low and High Level signals
Optional wired ACR-1 Remote Control for Output Level
All-weather rated - IPX6 rated!
Cage-free op-amps
ACX-600.1
2
ACX-600.1
Quick Start Guide
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturers instructions.
8. Do not install near any heat sources such as mufflers, silencers, exhaust
pipes, or other apparatus (including amplifiers) that produce heat.
9. WARNING: Improper installation may lead to permanent injury or death.
Installation of the apparatus must be done with great care by qualified
personnel, to prevent damage to fuel lines, power and other electrical
wiring, hydraulic brake lines, and other systems, that might compromise
vehicle safety.
10. Provide +12V and Ground wiring of sufficient size to ensure adequate
current to the amplifier. For the ACX-600.1 this means 8 gauge wire or
thicker.
11. Use rubber grommets to protect wiring whenever passing wires through
metal openings or bulkheads.
12. Only use attachments/accessories specified by the manufacturer.
13. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as the power
input terminals are damaged or objects have fallen into the apparatus,
does not operate normally, or has been dropped.
14. Fuses shall be replaced only with the correct type and fuse value, and
only when the apparatus is powered off.
15. Exposure to high sound pressure levels may lead to permanent hearing
loss. Take every precaution to protect your hearing.
The lightning flash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure, that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user of the presence of important operating and mainte-
nance (servicing) instructions in the literature accompanying the
appliance.
Caution: to reduce the risk of electric shock, do
not disassemble the apparatus, other than to
remove the top panel to access the controls.
There are no user-serviceable parts inside.
Refer servicing to qualified personnel.
Recycling notice: If the time comes and this apparatus has fulfilled
its destiny, do not throw it out into the trash. It has to be carefully
recycled for the good of mankind, by a facility specially equipped
for the safe recycling of electronic apparatii. Please contact your
local or state recycling leaders for assistance in locating a suitable
nearby recycling facility. Or, contact us and we might be able to
repair it for you.
Important Safety Instructions
3
1. Speaker Output Connect these wires to your subwoofer using
the included water resistant harness. Speaker wire may then be
crimped or soldered onto the bare leads. Use a decent sized wire
gauge as this baby is powerful!
2. Power Input Terminal +12V & Ground – Connect these wires
to the +12V and Negative binding posts of the vehicle battery
via one of two included harness options. You may use either the
included water resistant harness, or the included harness kit to
terminate your own custom-length water-resistant harness. Use
quality insulated wiring of the recommended wire gauge, such as
wire gauge 8 or thicker.
3. Remote Power Input Wire This wire connects to the 12V remote
trigger output of some head units and controls the on/off state of
the amplifier. Alternatively, you can use the GTO™ feature of the
amplifier so it will turn on when an speaker level signal is detected
at the RCA inputs.
Connections & Control Panel Features
123

Specyfikacje produktu

Marka: AudioControl
Kategoria: Receiver
Model: ACX-600.1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AudioControl ACX-600.1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Receiver AudioControl

Instrukcje Receiver

Najnowsze instrukcje dla Receiver

Mooer

Mooer SD30i Instrukcja

20 Września 2024
Peavey

Peavey CS 2000 Instrukcja

20 Września 2024
Focal

Focal FPX 5.1200 Instrukcja

19 Września 2024
DAP-Audio

DAP-Audio CX-2100 Instrukcja

19 Września 2024
LEA

LEA Connect 88D Instrukcja

19 Września 2024
Citronic

Citronic H1600 Instrukcja

19 Września 2024
Tangent

Tangent Ampster BT Instrukcja

19 Września 2024