Instrukcja obsługi Audio-Technica PRO42


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Audio-Technica PRO42 (2 stron) w kategorii mikrofon. Ta instrukcja była pomocna dla 29 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
PRO
42
MINIATURE UNIDIRECTIONAL
CONDENSER BOUNDARY
MICROPHONE
Frequency in Hertz
Response in dB
10 dB
20k10k5k2k1k50020010050
LEGEND 12" or more on axis
Frequency Response
pad minimizes mechanical coupling of surface
vibrations to the microphone. The low-profile
housing has a low-reectance black nish.
Operation and Maintenance
The symmetry and area of the mounting sur-
face directly affect the sensitivity of the
boundary microphone at low frequencies.
Ideally, the mounting surface should be circu-
lar; however, square or rectangular surfaces
are most often used. If the mounting surface
is rectangular, the smaller dimension tends to
determine low-frequency cutoff. The micro-
phone should be centered on the surface and
positioned with the front of the microphone
facing the sound source along the longer
dimension of the mounting surface. The
sound source should not be below, or higher
than 60° above, the plane of the mounting
surface.
Output is low impedance balanced. The output
connector mates with XLRF-type connectors.
The balanced signal appears across Pins 2
and 3, while the ground (shield) connection
is Pin 1. Output is phased so that positive
acoustic pressure produces positive voltage at
Pin 2 in accordance with industry convention.
DC phantom power (9-52 volts) must be
applied equally to Pins 2 and 3, with the
ground for the power supply connected to
Pin 1. This can be provided by a console or
mixer with built-in phantom voltage or with the
addition of an in-line phantom power supply,
such as the recommended Audio-Technica
CP8506 and AT8801 power supplies.
The high sensitivity of the PRO 42 ensures
useful output and an excellent match to most
mixer, tape recorder and amplifier inputs. It
will provide undistorted output even in sound
Description
The PRO 42 is a wide-range miniature con-
denser microphone with a hemi-cardioid
(half-space cardioid) polar pattern. It was
designed for surface-mounted applications in
high-quality sound reinforcement and other
demanding sound pickup situations. Its small
size makes the PRO 42 ideal for use in appli-
cations where minimum visibility is required.
The PRO 42 features a 25' (7.6 m) perma-
nently-attached miniature cable with an
XLRM-type connector, which allows it to be
plugged directly into an XLRF-type jack or
cable connector. The unit’s integral electronics
can be powered from any external 9V to 52V
DC phantom power source.
Audio-Technica design engineers have utilized
the newest low-mass technology in the quest
for superior performance. The charge is now
on the fixed back plate, rather than the moving
element. With the A-T fixed-charge “back plate”
construction, a gold-vaporized diaphragm just
2 microns thick (about 0.000079") can be
used. This reduces moving mass substantially,
improving frequency response and transient
response while reducing distortion.
Positioning a properly designed miniature
unidirectional microphone centrally on a large,
flat, unobstructed surface yields several dis-
tinct advantages. Directionality is increased
by 3 dB, promoting enhanced gain before
feedback and further suppression of ambient
noise. Sensitivity is increased for improved
signal-to-noise ratio. Phase distortion due to
reflected sound energy from the boundary
itself is eliminated.
The microphone element is enclosed in a
rugged case and protected by heavy
perforated steel. The rubber non-slip bottom
elds as loud as 134 dB SPL. However, due
to the high sensitivity, in some instances it
may be possible to overload sensitive input
stages. If distortion occurs,
first
check for
input
overload. In such cases, an attenuator
such as the Audio-Technica AT8202 may be
required between the mic and the electronics
input. (Also, many mixers provide “input pad
switches to reduce mic-input signal levels.)
While a modern condenser microphone is not
unduly sensitive to the environment, tempera-
ture extremes can be harmful. Exposure to
high temperatures can result in gradual and
permanent reduction of the output level. Avoid
leaving the microphone in the open sun or in
areas where temperatures exceed 110° F
(43° C) for long periods of time. Extremely
high humidity should also be avoided.
One-Year Limited Warranty
Audio-Technica microphones and accessories purchased in
the U.S.A. are warranted for one year from date of purchase
by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in
materials and workmanship. In event of such defect, product
will be repaired promptly without charge or, at our option,
replaced with a new product of equal or superior value if
delivered to A.T.U.S. or an Authorized Service Center,
prepaid, together with the sales slip or other proof of purchase
date.
Prior approval from A.T.U.S. is required for return.
This warranty excludes defects due to normal wear, abuse,
shipping damage, or failure to use product in accordance with
instructions. This warranty is void in the event of unauthorized
repair or modication.
For return approval and shipping information,
contact
the S ervice Depar tment, Audio-Tec hnica U.S ., Inc.,
1221 Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law,
A.T.U.S. will have no liability for any consequential,
incidental, or special damages; any warranty of mer-
chantability or fitness for particular purpose expires
when this warranty expires.
This warranty gives you specific legal rights, and you may
have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for
warranty details.
PRO
42
200 Hz
1 kHz
5 kHz
8 kHz
LEGEND
SCALE IS 5 DECIBELS PER DIVISION
90
60
120
30
150210
240
270
300
330
180
0
PRO 42 SPECIFICATIONS
Element ..................................................... Fixed-charge back plate
permanently polarized condenser
Polar Pattern ............................................. Half-cardioid (cardioid in hemisphere above
mounting surface)
Frequency Response .............................. 70-14,000 Hz
Open Circuit Sensitivity .......................... 38 dB (12.5 mV) re 1V at 1 Pa*
Impedance ................................................ 100 ohms
Maximum Input Sound Level .................. 134 dB SPL, 1 kHz at 1% T.H.D.
Signal-to-noise Ratio1.............................. 65 dB, 1 kHz at 1 Pa*
Dynamic Range (Typical) ......................... 105 dB, 1 kHz at Max SPL
Phantom Power Requirements ............... 9-52V DC, 2 mA typical
Weight (less cable) .................................... 1.2 oz (35 grams)
Dimensions .............................................. 1.44" (36.6 mm) max width,
2.14" (54.3 mm) max length,
0.61" (15.5 mm) height
Output Connector .................................... 3-pin XLRM-type
Cable ......................................................... 25' (7.6 m) long (permanently attached
to microphone), 0.10" (2.6 mm) diameter,
2-conductor, shielded cable
† In the interest of standards development, A.T.U.S. oers full details
on its test methods to other industry professionals on request.
* 1 Pascal = 10 dynes/cm 2= 10 microbars = 94 dB SPL
1Typical, A-weighted, using Audio Precision System One
Optional Accessories:
CP8201 line matching transformer
(Lo-Z to 50,000 ohms).
AT8202 adjustable in-line attenuator for use
with balanced Lo-Z microphones.
AT8314 2-conductor, shielded, vinyl-jacketed,
broadcast-type cable with XLRF-type connector
at microphone end, XLRM-type connector at
equipment end. Available in 10', 20', 25', 30', 50'
& 100' lengths.
CP8506 four-channel 48V phantom power
supply (AC powered).
AT8801 single-channel 48V phantom power
supply (AC powered).
Polar Pattern
Dimensions
25
7.6 m
2.68"
68.0 mm
2.14"
54.3 mm
36.6 mm
1.44"
2.6 mm
0.10"
19.0 mm
0.75"
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
Form No. 0320-0803-01-B/W © 1998 Audio-Technica U.S., Inc. Printed in U.S.A.


Specyfikacje produktu

Marka: Audio-Technica
Kategoria: mikrofon
Model: PRO42
Źródło zasilania: DC
Waga produktu: 35 g
Technologia łączności: Przewodowa
Częstotliwość mikrofonu: 70 - 14000 Hz
Czułość mikrofonu: 38 dB
Impedancja mikrofonu: 100 Ω
Napięcie pracy: 9 V
Typ zasilacza: DC
Zużycie energii: 2 mA
Typ przewodu: XLRM

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Audio-Technica PRO42, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje mikrofon Audio-Technica

Audio-Technica

Audio-Technica BP4073 Instrukcja

15 Października 2024
Audio-Technica

Audio-Technica AT4060 Instrukcja

14 Października 2024
Audio-Technica

Audio-Technica BP892xCH Instrukcja

12 Października 2024
Audio-Technica

Audio-Technica ATM610a Instrukcja

7 Października 2024
Audio-Technica

Audio-Technica BP894x Instrukcja

6 Października 2024
Audio-Technica

Audio-Technica XM1S Instrukcja

4 Października 2024
Audio-Technica

Audio-Technica U891RWb Instrukcja

4 Października 2024
Audio-Technica

Audio-Technica AT2031 Instrukcja

2 Października 2024

Instrukcje mikrofon

Najnowsze instrukcje dla mikrofon

Power Dynamics

Power Dynamics PD524 Instrukcja

15 Października 2024
Pyle

Pyle PDWM8225 Instrukcja

13 Października 2024
AKG

AKG WMS420 Instrukcja

13 Października 2024
Apart

Apart MDS.DEL Instrukcja

10 Października 2024
BOYA

BOYA BY-V4 Instrukcja

9 Października 2024
BOYA

BOYA BY-WM3T Instrukcja

9 Października 2024
Krom

Krom Kyp Instrukcja

9 Października 2024