Instrukcja obsługi Asrock H470M-HDV/M.2

Asrock płyta główna H470M-HDV/M.2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Asrock H470M-HDV/M.2 (82 stron) w kategorii płyta główna. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/82

Version 1.0

Published January 2021

No part of this documentation may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this documentation may or may not

be registered trademarks or copyrights of their respective companies, and are used

only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for

informational use only and subject to change without notice, and should not be

constructed as a commitment by ASRock. ASRock assumes no responsibility for

any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide

warranty of any kind, either expressed or implied, including but not limited to

the implied warranties or conditions of merchantability or tness for a particular

purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of prots, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/

perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian

Consumer Law. You are entitled to a replacement or refund for a major failure and

compensation for any other reasonably foreseeable loss or damage caused by our

goods. You are also entitled to have the goods repaired or replaced if the goods fail

to be of acceptable quality and the failure does not amount to a major failure. If

you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard

International call charges apply)

e terms HDMI® and HDMI High-Denition Multimedia Interface, and the

HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the

United States and other countries.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Motherboard Layout 6

1.4 I/O Panel 8

Chapter 2 Installation 10

2.1 Installing the CPU 11

2.2 Installing the CPU Fan and Heatsink 14

2.3 Installing Memory Modules (DIMM) 15

2.4 Expansion Slots (PCI Express Slots) 17

2.5 Jumpers Setup 18

2.6 Onboard Headers and Connectors 19

2.7 M.2_SSD (NGFF) Module Installation Guide (M2_1) 24

2.8 M.2 WiFi/BT Module Installation Guide (M2_2) 28

Chapter 3 Software and Utilities Operation 30

3.1 Installing Drivers 30

3.2 ASRock Motherboard Utility (A-Tuning) 31

3.2.1 Installing ASRock Motherboard Utility (A-Tuning) 31

3.2.2 Using ASRock Motherboard Utility (A-Tuning) 31

3.3 ASRock Live Update & APP Shop 34

3.3.1 UI Overview 34

3.3.2 Apps 35

3.3.3 BIOS & Drivers 38

3.3.4 Setting 39

Chapter 4 UEFI SETUP UTILITY 40

4.1 Introduction 40

4.2 EZ Mode 41

4.3 Advanced Mode 42

4.3.1 UEFI Menu Bar 42

4.3.2 Navigation Keys 43

4.4 Main Screen 44

4.5 OC Tweaker Screen 45

4.6 Advanced Screen 53

4.6.1 CPU Conguration 54

4.6.2 Chipset Conguration 56

4.6.3 Storage Conguration 59

4.6.4 Super IO Conguration 60

4.6.5 ACPI Conguration 61

4.6.6 USB Conguration 63

4.6.7 Trusted Computing 64

4.7 Tools 65

4.8 Hardware Health Event Monitoring Screen 67

4.9 Security Screen 70

4.10 Boot Screen 71

4.11 Exit Screen 74

English

H470M-HDV/M.2

Chapter 1 Introduction

ank you for purchasing ASRock H470M-HDV/M.2 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control.

It delivers excellent performance with robust design conforming to ASRock’s

commitment to quality and endurance.

In this documentation, Chapter 1 and 2 contains the introduction of the

motherboard and step-by-step installation guides. Chapter 3 contains the operation

guide of the soware and utilities. Chapter 4 contains the conguration guide of

the BIOS setup.

1.1 Package Contents

ASRock H470M-HDV/M.2 Motherboard (Micro ATX Form Factor)

ASRock H470M-HDV/M.2 Quick Installation Guide

ASRock H470M-HDV/M.2 Support CD

2 x Serial ATA (SATA) Data Cables (Optional)

2 x Screws for M.2 Sockets (Optional)

1 x I/O Panel Shield

Because the motherboard specications and the BIOS soware might be updated, the

content of this documentation will be subject to change without notice. In case any

modications of this documentation occur, the updated version will be available on

ASRock’s website without further notice. If you require technical support related to

this motherboard, please visit our website for specic information about the model

you are using. You may nd the latest VGA cards and CPU support list on ASRock’s

website as well. ASRock website http://www.asrock.com.

English

1.2 Specications

Platform Micro ATX Form Factor

Solid Capacitor design

CPU Supports 10th Gen Intel® CoreTM Processors (Socket 1200)

Digi Power design

7 Power Phase design

Supports Intel® Turbo Boost Max 3.0 Technology

Chipset Intel® H470

Memory Dual Channel DDR4 Memory Technology

2 x DDR4 DIMM Slots

Supports DDR4 2933/2800/2666/2400/2133 non-ECC, un-

buered memory

* Please refer to Memory Support List on ASRock's website for

more information. (http://www.asrock.com/)

* CoreTM (i9/i7) support DDR4 up to 2933; CoreTM (i5/i3),

Pentium® and Celeron® support DDR4 up to 2666.

Supports ECC UDIMM memory modules (operate in non-

ECC mode)

Max. capacity of system memory: 64GB

Supports Intel® Extreme Memory Prole (XMP) 2.0

15μ Gold Contact in DIMM Slots

Expansion

Slot

1 x PCI Express 3.0 x16 Slot

* Supports NVMe SSD as boot disks

2 x PCI Express 3.0 p7-x1 Slots

1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module

Graphics Intel® UHD Graphics Built-in Visuals and the VGA outputs

can be supported only with processors which are GPU

integrated.

Hardware Accelerated Codecs: AVC/H.264, HEVC/H.265

8bit, HEVC/H.265 10bit, VP8, VP9 8bit, VP9 10bit, MPEG 2,

MJPEG, VC-1

* VP9 10bit and VC-1 are for decode only.

* VP8 and VP9 encode are not supported by Windows OS.

English

H470M-HDV/M.2

Graphics, Media & Compute: Microso DirectX 12, OpenGL

4.5, Intel® Built In Visuals, Intel® Quick Sync Video, Hybrid /

Switchable Graphics, OpenCL 2.1

Display & Content Security: Rec. 2020 (Wide Color Gamut),

Microso PlayReady 3.0, Intel® SGX Content Protection,

UHD/HDR Blu-ray Disc

ree graphics output options: D-Sub, DVI-D and HDMI

Supports Triple Monitor

Supports HDMI 1.4 with max. resolution up to 4K x 2K

(4096x2160) @ 30Hz

Supports DVI-D with max. resolution up to 1920x1200 @

60Hz

Supports D-Sub with max. resolution up to 1920x1200 @

60Hz

Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

HBR (High Bit Rate Audio) with HDMI 1.4 Port (Compliant

HDMI monitor is required)

Supports HDCP 2.3 with DVI-D and HDMI 1.4 Ports

Supports 4K Ultra HD (UHD) playback with HDMI 1.4 Port

Audio 7.1 CH HD Audio (Realtek ALC897 Audio Codec)

Supports Surge Protection

LAN Gigabit LAN 10/100/1000 Mb/s

Giga PHY Intel® I219V

Supports Wake-On-LAN

Supports Lightning/ESD Protection

Supports Energy Ecient Ethernet 802.3az

Supports PXE

Rear Panel

I/O

1 x Antenna Bracket

1 x PS/2 Mouse/Keyboard Port

1 x D-Sub Port

1 x DVI-D Port

1 x HDMI Port

2 x USB 2.0 Ports (Supports ESD Protection)

4 x USB 3.2 Gen1 Ports (Supports ESD Protection)

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

LED)

HD Audio Jacks: Line in / Front Speaker / Microphone

English

Storage 4 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,

RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology

17), NCQ, AHCI and Hot Plug

1 x Ultra M.2 Socket (M2_1), supports M Key type

2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI Ex-

press module up to Gen3 p9-x4 (32 Gb/s)*

* Supports Intel® OptaneTM Technology

* Supports NVMe SSD as boot disks

* Supports ASRock U.2 Kit

Connector 1 x Print Port Header

1 x COM Port Header

1 x SPI TPM Header

1 x Chassis Intrusion and Speaker Header

1 x CPU Fan Connector (4-pin)

* e CPU Fan Connector supports the CPU fan of maximum

1A (12W) fan power.

1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan

Speed Control)

* e CPU/Water Pump Fan supports the water cooler fan of

maximum 2A (24W) fan power.

2 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan

Speed Control)

* e Chassis/Water Pump Fan supports the water cooler fan of

maximum 2A (24W) fan power.

* CPU_FAN2/WP, CHA_FAN1/WP and CHA_FAN2/WP can

auto detect if 3-pin or 4-pin fan is in use.

1 x 24 pin ATX Power Connector

1 x 8 pin 12V Power Connector

1 x Front Panel Audio Connector

2 x USB 2.0 Headers (Support 3 USB 2.0 ports) (Supports

ESD Protection)

2 x USB 3.2 Gen1 Headers (Support 4 USB 3.2 Gen1 ports)

(Supports ESD Protection)

BIOS

Feature

AMI UEFI Legal BIOS with multilingual GUI support

ACPI 6.0 Compliant wake up events

SMBIOS 2.7 Support

CPU Core/Cache, GT, DRAM, VPPM, PCH 1.05V, VCCST,

VCCSA Voltage Multi-adjustment

English

H470M-HDV/M.2

Hardware

Monitor

Fan Tachometer: CPU, CPU/Water Pump, Chassis/Water

Pump Fans

Quiet Fan (Auto adjust chassis fan speed by CPU tempera-

ture): CPU, CPU/Water Pump, Chassis/Water Pump Fans

Fan Multi-Speed Control: CPU, CPU/Water Pump, Chassis/

Water Pump Fans

CASE OPEN detection

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,

VPPM, PCH, VCCSA, VCCST

OS Microso® Windows® 10 64-bit

Certica-

tions

FCC, CE

ErP/EuP ready (ErP/EuP ready power supply is required)

Please realize that there is a certain risk involved with overclocking, including

adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using

third-party overclocking tools. Overclocking may aect your system’s stability, or

even cause damage to the components and devices of your system. It should be done

at your own risk and expense. We are not responsible for possible damage caused by

overclocking.

* For detailed product information, please visit our website:

http://www.asrock.com

English

1.3 Motherboard Layout

English

H470M-HDV/M.2

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 CPU Fan Connector (CPU_FAN1)

3 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

4 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)

5 ATX Power Connector (ATXPWR1)

6 USB 3.2 Gen1 Header (USB3_1_2)

7 SATA3 Connector (SATA3_0) (Upper)

8 SATA3 Connector (SATA3_1) (Lower)

9 SATA3 Connector (SATA3_2) (Upper)

10 SATA3 Connector (SATA3_3) (Lower)

11 SPI TPM Header (SPI_TPM_J1)

12 System Panel Header (PANEL1)

13 Chassis Intrusion and Speaker Header (SPK_CI1)

14 Chassis/Water Pump Fan Connector (CHA_FAN2/WP)

15 USB 2.0 Header (USB_5)

16 USB 2.0 Header (USB3_4)

17 USB 3.2 Gen1 Header (USB3_5_6)

18 COM Port Header (COM1)

19 Print Port Header (LPT1)

20 Front Panel Audio Header (HD_AUDIO1)

21 Clear CMOS Jumper (CLRMOS1)

22 CPU/Water Pump Fan Connector (CPU_FAN2/WP)

English

1.4 I/O Panel

No. Description No. Description

1 D-Sub Port 7 USB 3.2 Gen1 Ports (USB3_3_4)

2 PS/2 Mouse/Keyboard Port 8 USB 2.0 Ports (USB1_2)

3 LAN RJ-45 Port* 9 Antenna Bracket

4 Line In (Light Blue)** 10 USB 3.2 Gen1 Ports (USB3_7_8)

5 Front Speaker (Lime)** 11 DVI-D Port

6 Microphone (Pink)** 12 HDMI Port

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection

Blinking Data Activity Orange 100Mbps connection

On Link Green 1Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

12 671011

English

H470M-HDV/M.2

** Function of the Audio Ports in 7.1-channel Conguration:

Port Function

Light Blue (Rear panel) Rear Speaker Out

Lime (Rear panel) Front Speaker Out

Pink (Rear panel) Central /Subwoofer Speaker Out

Lime (Front panel) Side Speaker Out

English

is is a Micro ATX form factor motherboard. Before you install the motherboard,

study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

components. Failure to do so may cause physical injuries and damages to motherboard

components.

In order to avoid damage from static electricity to the motherboard’s components,

NEVER place your motherboard directly on a carpet. Also remember to use a grounded

wrist strap or touch a safety grounded object before you handle the components.

Hold components by the edges and do not touch the ICs.

Whenever you uninstall any components, place them on a grounded anti-static pad or

in the bag that comes with the components.

When placing screws to secure the motherboard to the chassis, please do not over-

tighten the screws! Doing so may damage the motherboard.

Chapter 2 Installation

English

H470M-HDV/M.2

2.1 Installing the CPU

1. Before you insert the 1200-Pin CPU into the socket, please check if the PnP cap

is on the socket, if the CPU surface is unclean, or if there are any in the bent pins

socket. Do not force to insert the CPU into the socket if above situation is found.

Otherwise, the CPU will be seriously damaged.

2. Unplug all power cables before installing the CPU.

English

H470M-HDV/M.2

Please save and replace the cover if the processor is removed. e cover must be

placed if you wish to return the motherboard for aer service.

English

2.2 Installing the CPU Fan and Heatsink

1 2

CPU_FAN

English

H470M-HDV/M.2

2.3 Installing Memory Modules (DIMM)

is motherboard provides two 288-pin DDR4 (Double Data Rate 4) DIMM slots,

and supports Dual Channel Memory Technology.

e DIMM only ts in one correct orientation. It will cause permanent damage to

the motherboard and the DIMM if you force the DIMM into the slot at incorrect

orientation.

1. For dual channel conguration, you always need to install identical (the same

brand, speed, size and chip-type) DDR4 DIMM pairs.

2. It is unable to activate Dual Channel Memory Technology with only one memory

module installed.

3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4

slot; otherwise, this motherboard and DIMM may be damaged.

English

H470M-HDV/M.2

2.4 Expansion Slots (PCI Express Slots)

ere are 3 PCI Express slots on the motherboard.

PCIe slots:

PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.

PCIE2 (PCIe 3.0 p22-x1 slot) is used for PCI Express p22-x1 lane width cards.

PCIE3 (PCIe 3.0 p22-x1 slot) is used for PCI Express p22-x1 lane width cards.

Before installing an expansion card, please make sure that the power supply is

switched o or the power cord is unplugged. Please read the documentation of the

expansion card and make necessary hardware settings for the card before you start

the installation.

English

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is

“Open”.

Clear CMOS Jumper

(CLRMOS1)

(see p.6, No. 21)

Short: Clear CMOS

Open: Default

CLRMOS1 allows you to clear the data in CMOS. e data in CMOS includes

system setup information such as system password, date, time, and system setup

parameters. To clear and reset the system parameters to default setup, please turn

o the computer and unplug the power cord, then use a jumper cap to short the

pins on CLRMOS1 for 3 seconds. Please remember to remove the jumper cap aer

clearing the CMOS. If you need to clear the CMOS when you just nish updating

the BIOS, you must boot up the system rst, and then shut it down before you do

the clear-CMOS action.

2-pin Jumper

If you clear the CMOS, the case open may be detected. Please adjust the BIOS option

“Clear Status” to clear the record of previous chassis intrusion status.

English

H470M-HDV/M.2

2.6 Onboard Headers and Connectors

System Panel Header

(9-pin PANEL1)

(see p.6, No. 12)

Connect the power

button, reset button and

system status indicator on

the chassis to this header

according to the pin

assignments below. Note

the positive and negative

pins before connecting

the cables.

Chassis Intrusion and

Speaker Header

(7-pin SPK_CI1)

(see p.6, No. 13)

Please connect the

chassis intrusion and the

chassis speaker to this

header.

GND

RE S E T #

PWRBT N#

PL E D-

PL E D+

GND

HD L E D -

HD L E D +

GND

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over

these headers and connectors. Placing jumper caps over the headers and connectors

will cause permanent damage to the motherboard.

PWRBTN (Power Button):

Connect to the power button on the chassis front panel. You may congure the way

to turn o your system using the power button.

RESET (Reset Button):

Connect to the reset button on the chassis front panel. Press the reset button to

restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. e LED is on when

the system is operating. e LED keeps blinking when the system is in S1/S3 sleep

state. e LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. e LED is on

when the hard drive is reading or writing data.

e front panel design may dier by chassis. A front panel module mainly consists

of power button, reset button, power LED, hard drive activity LED, speaker and etc.

When connecting your chassis front panel module to this header, make sure the wire

assignments and the pin assignments are matched correctly.

+5V

D UM M Y

S IG N AL

GND

D UM M Y

SPEA KER

D UM M Y

English

Serial ATA3 Connectors

Right Angle:

(SATA3_0:

see p.6, No. 7) (Upeper)

(SATA3_1:

see p.6, No. 8) (Lower)

(SATA3_2:

see p.6, No. 9) (Upper)

(SATA3_3:

see p.6, No. 10) (Lower)

ese four SATA3

connectors support SATA

data cables for internal

storage devices with up to

6.0 Gb/s data transfer rate.

USB 2.0 Headers

(9-pin USB3_4)

(see p.6, No. 16)

(4-pin USB_5)

(see p.6, No. 15)

ere are two headers on

this motherboard.

USB 3.2 Gen1 Headers

(19-pin USB3_1_2)

(see p.6, No. 6)

(19-pin USB3_5_6)

(see p.6, No. 17)

ere are two headers on

this motherboard. Each

USB 3.2 Gen1 header can

support two ports.

Front Panel Audio Header

(9-pin HD_AUDIO1)

(see p.6, No. 20)

is header is for

connecting audio devices

to the front audio panel.

DUMMY

GND

P+

P-

USB_P WR

P+

P-

USB_P WR

In tA _PB _D +

Du mm y

In tA _PB _D -

GN D

In tA _PB _S ST X +

GN D

In tA _PB _S ST X -

In tA _PB _S SR X +

In tA _PB _S SR X -

Vb usVb us

Vb us

In tA _PA_ SS RX-

In tA _PA_ SS RX+

GN D

In tA _PA_ SS TX-

In tA _PA_ SS TX+

GN D

In tA _PA_ D-

In tA _PA_ D+

J _SEN SE

O UT2_ L

M IC_R ET

P RESE NCE#

GND

O UT2_ R

M IC2_ R

M IC2_ L

OUT_R ET

SATA3_1

SATA3_0

SATA3_3

SATA3_2

ID In tA_ P_ D+

In tA_ P_ D-

GN D

In tA_ P_ SST X+

In tA_ P_ SST X-

GN D

In tA_ P_ SSR X+

Vb us

In tA_ P_ D+

In tA_ P_ D-

GN D

In tA_ P_ SST X+

In tA_ P_ SST X-

GN D

In tA_ P_ SSR X+

In tA_ P_ SSR X-

Vb us

In tA_ P_ SSR X-

USB_PW R

P- P+

GND

English

H470M-HDV/M.2

Chassis/Water Pump Fan

Connectors

(4-pin CHA_FAN1/WP)

(see p.6, No. 4)

(4-pin CHA_FAN2/WP)

(see p.6, No. 14)

is motherboard provides two

4-Pin water cooling

chassis

fan

connectors. If you plan to con-

nect a 3-Pin

chassis

water cooler

fan, please connect it to Pin 1-3.

CPU Fan Connector

(4-pin CPU_FAN1)

(see p.6, No. 2)

is motherboard

provides a 4-Pin CPU fan

(Quiet Fan) connector.

If you plan to connect a

3-Pin CPU fan, please

connect it to Pin 1-3.

CPU/Water Pump Fan

Connector

(4-pin CPU_FAN2/WP)

(see p.6, No. 22)

is motherboard

provides a 4-Pin water

cooling CPU fan

connector. If you plan

to connect a 3-Pin CPU

water cooler fan, please

connect it to Pin 1-3.

1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis

must support HDA to function correctly. Please follow the instructions in our

manual and chassis manual to install your system.

2. If you use an AC’97 audio panel, please install it to the front panel audio header by

the steps below:

A. Connect Mic_IN (MIC) to MIC2_L.

B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C. Connect Ground (GND) to Ground (GND).

D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to

connect them for the AC’97 audio panel.

E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel

and adjust “Recording Volume”.

GND

F AN_V OLTAGE

CHA_F AN_S PEED

FAN _SPE ED_CO NTROL

4 3 2 1

GN D

FAN _V OLTAG E_ CO NT RO L

FAN _S PE ED

FAN _S PE ED _C ON TR OL

CPU_F

FAN_ VOLT AGE

GND

AN_SPE ED

FAN_S PEED_C ONTROL

4 3 2 1

G ND

+12V

C PU_FAN_ SPEED

FAN_ SPEE D_CON TROL

1 2 3 4

English

ATX Power Connector

(24-pin ATXPWR1)

(see p.6, No. 5)

is motherboard pro-

vides a 24-pin ATX power

connector. To use a 20-pin

ATX power supply, please

plug it along Pin 1 and Pin

13.

ATX 12V Power

Connector

(8-pin ATX12V1)

(see p.6, No. 1)

is motherboard

provides a 8-pin ATX 12V

power connector. To use a

4-pin ATX power supply,

please plug it along Pin 1

and Pin 5.

*Warning: Please make

sure that the power cable

connected is for the CPU

and not the graphics

card. Do not plug the

PCIe power cable to this

connector.

SPI TPM Header

(13-pin SPI_TPM_J1)

(see p.6, No. 11)

is connector supports SPI

Trusted Platform Module (TPM)

system, which can securely store

keys, digital certicates, pass-

words, and data. A TPM system

also helps enhance network

security, protects digital

identities, and ensures platform

integrity.

Serial Port Header

(9-pin COM1)

(see p.6, No. 18)

is COM1 header

supports a serial port

module.

4 1

8 5

SPI _ DQ3

+3. 3 V

SPI _ DQ2

SPI _ CS0

Dum m y

CLK

SPI _ MISO

SPI _ MOSI

GND

SPI _ TPM_C S#

RST #

RSM R ST#

TPM _ PIRQ

CCT S# 1

RRTS # 1

DDSR# 1

DDT R# 1

RR X D1

GND

TT X D1

DDCD# 1

RRI #1

English

H470M-HDV/M.2

Print Port Header

(25-pin LPT1)

(see p.6, No. 19)

is is an interface

for print port cable

that allows convenient

connection of printer

devices.

AFD #

ERR OR#

PIN IT# GND

SLI N#

STB #

SPD 0

SPD 1

SPD 2

SPD 3

SPD 4

SPD 5

SPD 6

SPD 7

ACK #

BUS Y

PESL CT

English

2.7 M.2_SSD (NGFF) Module Installation Guide (M2_1)

The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and

versatile card edge connector that aims to replace mPCIe and mSATA. The Ultra M.2

Socket (M2_1) supports M Key type 2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI

Express module up to Gen3 p29-x4 (32 Gb/s).

Installing the M.2_SSD (NGFF) Module

Step 1

Prepare a M.2_SSD (NGFF) module

and the screw.

Step 2

Depending on the PCB type and

length of your M.2_SSD (NGFF)

module, nd the corresponding nut

location to be used.

No. 1 2

Nut Location A B

PCB Length 6cm 8cm

Module Type Type2260 Type 2280

English

H470M-HDV/M.2

Step 3

Move the stando based on the

module type and length.

e stando is placed at the nut

location B by default. Skip Step 3 and

4 and go straight to Step 5 if you are

going to use the default nut.

Otherwise, release the stando by

hand.

Step 4

Peel o the yellow protective lm on

the nut to be used. Hand tighten the

stando into the desired nut location

on the motherboard.

Step 5

Gently insert the M.2 (NGFF) SSD

module into the M.2 slot. Please

be aware that the M.2 (NGFF) SSD

module only ts in one orientation.

Step 6

Tighten the screw with a screwdriver

to secure the module into place.

Please do not overtighten the screw as

this might damage the module.

AB 20o

English

M.2_SSD (NGFF) Module Support List

Vendor Interface P/N

ADATA SATA3 AXNS330E-32GM-B

ADATA SATA3 AXNS381E-128GM-B

ADATA SATA3 AXNS381E-256GM-B

ADATA SATA3 ASU800NS38-256GT-C

ADATA SATA3 ASU800NS38-512GT-C

ADATA PCIe3 x4 ASX7000NP-128GT-C

ADATA PCIe3 x4 ASX8000NP-256GM-C

ADATA PCIe3 x4 ASX7000NP-256GT-C

ADATA PCIe3 x4 ASX8000NP-512GM-C

ADATA PCIe3 x4 ASX7000NP-512GT-C

Apacer PCIe3 x4 AP240GZ280

Corsair PCIe3 x4 CSSD-F240GBMP500

Crucial SATA3 CT120M500SSD4

Crucial SATA3 CT240M500SSD4

Intel SATA3 Intel SSDSCKGW080A401/80G

Intel PCIe3 x4 SSDPEKKF256G7

Intel PCIe3 x4 SSDPEKKF512G7

Kingston SATA3 SM2280S3

Kingston PCIe3 x4 SKC1000/480G

Kingston PCIe2 x4 SH2280S3/480G

OCZ PCIe3 x4 RVD400-M2280-512G (NVME)

PATRIOT PCIe3 x4 PH240GPM280SSDR NVME

Plextor PCIe3 x4 PX-128M8PeG

Plextor PCIe3 x4 PX-1TM8PeG

Plextor PCIe3 x4 PX-256M8PeG

Plextor PCIe3 x4 PX-512M8PeG

Plextor PCIe PX-G256M6e

Plextor PCIe PX-G512M6e

Samsung PCIe3 x4 SM961 MZVPW128HEGM (NVM)

Samsung PCIe3 x4 PM961 MZVLW128HEGR (NVME)

Samsung PCIe3 x4 960 EVO (MZ-V6E250) (NVME)

Samsung PCIe3 x4 960 EVO (MZ-V6E250BW) (NVME)

Samsung PCIe3 x4 SM951 (NVME)

Samsung PCIe3 x4 SM951 (MZHPV256HDGL)

Samsung PCIe3 x4 SM951 (MZHPV512HDGL)

Samsung PCIe3 x4 SM951 (NVME)

Samsung PCIe x4 XP941-512G (MZHPU512HCGL)

SanDisk PCIe SD6PP4M-128G

SanDisk PCIe SD6PP4M-256G

Team SATA3 TM4PS4128GMC105

Team SATA3 TM4PS4256GMC105

Team SATA3 TM8PS4128GMC105

Team SATA3 TM8PS4256GMC105

English

H470M-HDV/M.2

TEAM PCIe3 x4 TM8FP2240G0C101

TEAM PCIe3 x4 TM8FP2480GC110

Transcend SATA3 TS256GMTS400

Transcend SATA3 TS512GMTS600

Transcend SATA3 TS512GMTS800

V-Color SATA3 VLM100-120G-2280B-RD

V-Color SATA3 VLM100-240G-2280RGB

V-Color SATA3 VSM100-240G-2280

V-Color SATA3 VLM100-240G-2280B-RD

WD SATA3 WDS100T1B0B-00AS40

WD SATA3 WDS240G1G0B-00RC30

WD PCIe3 x4 WDS256G1X0C-00ENX0 (NVME)

WD PCIe3 x4 WDS512G1X0C-00ENX0 (NVME)

For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for

details: http://www.asrock.com

English

2.8 M.2 WiFi/BT Module Installation Guide (M2_2)

e M.2, also known as the Next Generation Form Factor (NGFF), is a small size and

versatile card edge connector that aims to replace mPCIe and mSATA. e M.2 Socket (Key

E) supports type 2230 WiFi/BT module.

* e M.2 socket does not support SATA M.2 SSDs.

Installing the WiFi/BT module

Step 1

Prepare a type 2230 WiFi/BT module

and the screw.

PCB Length: 3cm

Module Type: Type2230

Step 2

Find the nut location to be used.

English

H470M-HDV/M.2

A20o

Step 3

Gently insert the WiFi/BT module

into the M.2 slot. Please be aware

that the module only ts in one

orientation.

Step 4

Tighten the screw with a screwdriver

to secure the module into place.

Please do not overtighten the screw as

this might damage the module.

English

Chapter 3 Software and Utilities Operation

3.1 Installing Drivers

e Support CD that comes with the motherboard contains necessary drivers and

useful utilities that enhance the motherboard’s features.

Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM drive. e CD

automatically displays the Main Menu if “AUTORUN” is enabled in your computer.

If the Main Menu does not appear automatically, locate and double click on the le

“ASRSETUP.EXE” in the Support CD to display the menu.

Drivers Menu

e drivers compatible to your system will be auto-detected and listed on the

support CD driver page. Please click or follow the order from top to Install All

bottom to install those required drivers. erefore, the drivers you install can work

properly.

Utilities Menu

e Utilities Menu shows the application soware that the motherboard supports.

Click on a specic item then follow the installation wizard to install it.

English

H470M-HDV/M.2

3.2 ASRock Motherboard Utility (A-Tuning)

ASRock Motherboard Utility (A-Tuning) is ASRock’s multi purpose soware suite

with a new interface, more new features and improved utilities.

3.2.1 Installing ASRock Motherboard Utility (A-Tuning)

ASRock Motherboard Utility (A-Tuning) can be downloaded from ASRock Live

Update & APP Shop. Aer the installation, you will nd the icon “ASRock Mother-

board Utility (A-Tuning)“ on your desktop. Double-click the

“ASRock Motherboard Utility (A-Tuning)“ icon, ASRock Motherboard Utility

(A-Tuning) main menu will pop up.

3.2.2 Using ASRock Motherboard Utility (A-Tuning)

ere are four sections in ASRock Motherboard Utility (A-Tuning) main menu:

Operation Mode, System Info, FAN-Tastic Tuning and Settings.

Operation Mode

Choose an operation mode for your computer.

English

System Info

View information about the system.

*e System Browser tab may not appear for certain models.

FAN-Tastic Tuning

Congure up to ve dierent fan speeds using the graph. e fans will automatically shi

to the next speed level when the assigned temperature is met.

English

H470M-HDV/M.2

Settings

Congure ASRock ASRock Motherboard Utility (A-Tuning). Click to select "Auto

run at Windows Startup" if you want ASRock Motherboard Utility (A-Tuning) to

be launched when you start up the Windows operating system.

English

3.3 ASRock Live Update & APP Shop

e ASRock Live Update & APP Shop is an online store for purchasing and

downloading soware applications for your ASRock computer. You can quickly and

easily install various apps and support utilities. With ASRock Live Update & APP

Shop, you can optimize your system and keep your motherboard up to date simply

with a few clicks.

Double-click on your desktop to access ASRock Live Update & APP Shop

utility.

*You need to be connected to the Internet to download apps from the ASRock Live Update & APP Shop.

3.3.1 UI Overview

Category Panel: e category panel contains several category tabs or buttons that

when selected the information panel below displays the relative information.

Information Panel: e information panel in the center displays data about the

currently selected category and allows users to perform job-related tasks.

Hot News: e hot news section displays the various latest news. Click on the image

to visit the website of the selected news and know more.

Information Panel

Hot News

Category Panel

English

H470M-HDV/M.2

3.3.2 Apps

When the "Apps" tab is selected, you will see all the available apps on screen for you

to download.

Installing an App

Step 1

Find the app you want to install.

e most recommended app appears on the le side of the screen. e other various

apps are shown on the right. Please scroll up and down to see more apps listed.

You can check the price of the app and whether you have already intalled it or not.

- e red icon displays the price or "Free" if the app is free of charge.

- e green "Installed" icon means the app is installed on your computer.

Step 2

Click on the app icon to see more details about the selected app.

English

Step 3

If you want to install the app, click on the red icon to start downloading.

Step 4

When installation completes, you can nd the green "Installed" icon appears on the

upper right corner.

To uninstall it, simply click on the trash can icon .

*e trash icon may not appear for certain apps.

English

H470M-HDV/M.2

Upgrading an App

You can only upgrade the apps you have already installed. When there is an

available new version for your app, you will nd the mark of "New Version"

appears below the installed app icon.

Step 1

Click on the app icon to see more details.

Step 2

Click on the yellow icon to start upgrading.

English

3.3.3 BIOS & Drivers

Installing BIOS or Drivers

When the "BIOS & Drivers" tab is selected, you will see a list of recommended or

critical updates for the BIOS or drivers. Please update them all soon.

Step 1

Please check the item information before update. Click on to see more details.

Step 2

Click to select one or more items you want to update.

Step 3

Click Update to start the update process.

English

H470M-HDV/M.2

3.3.4 Setting

In the "Setting" page, you can change the language, select the server location, and

determine if you want to automatically run the ASRock Live Update & APP Shop

on Windows startup.

English

Chapter 4 UEFI SETUP UTILITY

4.1 Introduction

is section explains how to use the UEFI SETUP UTILITY to congure your

system. You may run the UEFI SETUP UTILITY by pressing <F2> or <Del> right

aer you power on the computer, otherwise, the Power-On-Self-Test (POST) will

continue with its test routines. If you wish to enter the UEFI SETUP UTILITY aer

POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the

reset button on the system chassis. You may also restart by turning the system o

and then back on.

Because the UEFI soware is constantly being updated, the following UEFI setup

screens and descriptions are for reference purpose only, and they may not exactly

match what you see on your screen.

English

H470M-HDV/M.2

4.2 EZ Mode

e EZ Mode screen appears when you enter the BIOS setup program by default. EZ

mode is a dashboard which contains multiple readings of the system’s current status.

You can check the most crucial information of your system, such as CPU speed,

DRAM frequency, SATA information, fan speed, etc.

Press <F6> or click the "Advanced Mode" button at the upper right corner of the

screen to switch to "Advanced Mode" for more options.

1 2 3 4 5 6

No. Function

1Help

2Load UEFI Defaults

3Save Changes and Exit

4Discard Changes

5Change Language

6Switch to Advanced Mode

English

4.3 Advanced Mode

e Advanced Mode provides more options to congure the BIOS settings. Refer to

the following sections for the detailed congurations.

To access the EZ Mode, press <F6> or click the "EZ Mode" button at the upper right

corner of the screen.

4.3.1 UEFI Menu Bar

e top of the screen has a menu bar with the following selections:

Main For setting system time/date information

OC Tweaker For overclocking congurations

Advanced For advanced system congurations

Tool Useful tools

H/W Monitor Displays current hardware status

Security For security settings

Boot For conguring boot settings and boot priority

Exit Exit the current screen or the UEFI Setup Utility

English

H470M-HDV/M.2

4.3.2 Navigation Keys

Use < > key or < > key to choose among the selections on the menu bar, and

use < > key or < > key to move the cursor up or down to select items, then

press <Enter> to get into the sub screen. You can also use the mouse to click your

required item.

Please check the following table for the descriptions of each navigation key.

Navigation Key(s) Description

+ / - To change option for the selected items

<Tab> Switch to next function

<PGUP> Go to the previous page

<PGDN> Go to the next page

<HOME> Go to the top of the screen

<END> Go to the bottom of the screen

<F1> To display the General Help Screen

<F5> Add / Remove Favorite

<F7> Discard changes and exit the SETUP UTILITY

<F9> Load optimal default values for all the settings

<F10> Save changes and exit the SETUP UTILITY

<F12> Print screen

<ESC> Jump to the Exit Screen or exit the current screen

English

4.4 Main Screen

When you enter the UEFI SETUP UTILITY, the Main screen will appear and

display the system overview.

My Favorite

Display your collection of BIOS items. Press F5 to add/remove your favorite items.

e availability and location of BIOS settings can be dierent for dierent models

and BIOS versions.

English

H470M-HDV/M.2

4.5 OC Tweaker Screen

In the OC Tweaker screen, you can set up overclocking features.

CPU Conguration

AVX2 Ratio Oset

AVX2 Ratio Oset species a negative oset from the CPU Ratio for AVX work-

loads. AVX is a more stressful workload that lower the AVX ratio to ensure maxi-

mum possible ratio for SSE workloads.

GT Frequency

Congure the frequency of the integrated GPU.

BCLK Spread Spectrum

Enable BCLK Spread Spectrum to reduce electromagnetic interference for passing

EMI tests. Disable to achieve higher clock speeds when overclocking.

Because the UEFI soware is constantly being updated, the following UEFI setup

screens and descriptions are for reference purpose only, and they may not exactly

match what you see on your screen.

English

BCLK Aware Adaptive Voltage

BCLK Aware Adaptive Voltage enable/disable. When enabled, pcode will be aware

of the BCLK frequency when calculating the CPU V/F curves. is is ideal for

BCLK OC to avoid high voltage overrides.

Boot Performance Mode

Select the performance state that the BIOS will set before OS hando.

FCLK Frequency

Congure the FCLK Frequency.

Ring to Core Ratio Oset

Disable Ring to Core Ratio Oset so the ring and core can run at the same fre-

quency.

Intel SpeedStep Technology

Intel SpeedStep technology allows processors to switch between multiple frequen-

cies and voltage points for better power saving and heat dissipation.

Intel Turbo Boost Technology

Intel Turbo Boost Technology enables the processor to run above its base operating

frequency when the operating system requests the highest performance state.

Intel Speed Shift Technology

Enable/Disable Intel Speed Shi Technology support. Enabling will expose the

CPPC v2 interface to allow for hardware controlled P-states.

Intel Thermal Velocity Boost Voltage Optimizations

is service controls thermal based voltage optimizations for processors that

implment the Intel ermal Velocity Boost (TVB) feature.

DRAM Conguration

Memory Information

Allows users to browse the serial presence detect (SPD) and Intel extreme memory prole

(XMP) for DDR4 modules.

DRAM Timing Conguration

Load XMP Setting

Load XMP settings to overclock the memory and perform beyond standard specications.

English

H470M-HDV/M.2

DRAM Reference Clock

Select Auto for optimized settings.

DRAM Frequency

If [Auto] is selected, the motherboard will detect the memory module(s) inserted

and assign the appropriate frequency automatically.

Primary Timing

CAS# Latency (tCL)

e time between sending a column address to the memory and the beginning of the data

in response.

RAS# to CAS# Delay and Row Precharge (tRCDtRP)

RAS# to CAS# Delay : e number of clock cycles required between the opening of a row

of memory and accessing columns within it.

Row Precharge: e number of clock cycles required between the issuing of the precharge

command and opening the next row.

RAS# Active Time (tRAS)

e number of clock cycles required between a bank active command and issuing the

precharge command.

Command Rate (CR)

e delay between when a memory chip is selected and when the rst active command can

be issued.

Secondary Timing

Write Recovery Time (tWR)

e amount of delay that must elapse aer the completion of a valid write operation,

before an active bank can be precharged.

Refresh Cycle Time (tRFC)

e number of clocks from a Refresh command until the rst Activate command to

the same rank.

RAS to RAS Delay (tRRD_L)

e number of clocks between two rows activated in dierent banks of the same

rank.

Specyfikacje produktu

Marka:	Asrock
Kategoria:	płyta główna
Model:	H470M-HDV/M.2
Szerokość produktu:	226 mm
Głębokość produktu:	188 mm
Certyfikaty:	FCC, CE, ErP/EuP ready
Wyjścia słuchawkowe:	1
Obsługiwany typ USB:	USB Typu-A
Obsługiwane systemy operacyjne Windows:	Windows 10 x64
Przeznaczenie:	PC
Ilość portów Ethernet LAN (RJ-45):	1
Wi-Fi:	Nie
Przewody:	SATA
Kod zharmonizowanego systemu (HS):	84733020
Kanały wyjścia audio:	7.1 kan.
Liczba portów USB 2.0:	2
Przewodowa sieć LAN:	Tak
Ilość obsługiwanych rozmiarów dysków pamięci:	1
Obsługiwane rodzaje dysków:	HDD & SSD
Producent procesora:	Intel
Ilość portów USB 3.2 Gen 1 (3.1 Gen 1) Typu-A:	4
Rodzaj chłodzenia:	Aktywne
Obsługiwane rodzaje pamięci:	DDR4-SDRAM
Typ slotów pamięci:	DIMM
Liczba gniazd pamięci:	2
Bez kody korekcyjnego:	Tak
Obsługiwane pojemności modułów pamięci:	2GB, 4GB, 8GB, 16GB
Obsługiwane prędkości zegara pamięci:	2133,2400,2666,2800,2933 MHz
Maksymalna pojemność pamięci:	64 GB
Obsługa kanałów pamięci:	Dwukanałowy
Gniazdo procesora:	LGA 1200 (Socket H5)
Procesor:	Intel Celeron, Intel Core i3, Intel Core i5, Intel Core i7, Intel Core i9, Intel Pentium, Intel Pentium G
Rodzina płyt z chipsetami:	Intel
Rodzaj płyty:	micro ATX
Układ płyty głównej:	Intel H470
Poziomy raid:	0, 1,5, 10
Typ BIOS:	UEFI AMI
Liczba gniazd M.2 (M):	1
Gniazdo zasilania ATX (24-pin):	Tak
Złącze zasilacza EPS (8-pin):	Tak
Ilość złączy SATA III:	4
Ilość gniazd USB 2.0:	2
Łącza USB 3.2 Gen 1 (3.1 Gen 1):	2
Gniazdo wentylatora procesora:	Tak
Ilość gniazd w podstawie wentylatora:	2
Złącze audio na przednim panelu:	Tak
Złącze TPM:	Tak
Gniazdo na obudowie:	Tak
Liczba portów PS/2:	1
Ilość portów DVI-D:	1
Ilość portów HDMI:	1
Mikrofon:	Tak
Zawiera sterowniki:	Tak
Układ audio:	Realtek ALC897
Liczba otworów montażowych:	6
Pamięć niebuforowana:	Tak
Gniazda PCI Express x16 (Gen 3.x):	1
Wspierane interfejsy dysków twardych:	SATA III, Ultra M.2
Liczba obsługiwanych HDD:	4
Maks. rozdzielczość:	4096 x 2160 px
Wersja DirectX:	12.0
Liczba obsługiwanych wyświetlaczy:	3
Rodzaj interfejsu sieci Ethernet:	Gigabit Ethernet
Kontroler LAN:	Intel® I219-V
Funkcja Wake-On-LAN:	Tak
Złącza zasilania Peripheral (Molex) (4-pin):	1
Liczba portów VGA (D-Sub):	1
Wersja HDMI:	1.4
HDCP:	Tak
Dołączone oprogramowanie:	- ASRock Motherboard Utility (A-Tuning)\n- ASRock XFast LAN
Obsługiwane gniazda procesora:	LGA 1200 (Socket H5)
Monitorowanie stanu komputera:	CPU, FAN, Temperature, Voltage
Złącze zasilania 12V:	Tak
Rozmiar pamięci BIOS:	128 Mbit
Wersja ACPI:	6.0
Wersja systemu BIOS (SMBIOS):	2.7
Gniazda PCI Express x1 (Gen 3.x):	1
Złącze równoległe:	Tak
Wtyczka Jack anteny WiFi-AP:	1
Ilość gniazd COM:	1
Wersja OpenGL:	4.5