Instrukcja obsługi Ariston Thermo A1637

Ariston Thermo pralka A1637

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ariston Thermo A1637 (12 stron) w kategorii pralka. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
Contents
WASHING MACHINE
Instruction booklet
Installation, 2-3
Unpacking
Remove the transit fixings
Levelling
Water connections
Drainage and electrical connections
Technical details
Washing machine description, 4-5
Control panel
LEDs
Starting and programmes, 6
Briefly: how to start a programme
Programmes table
Personalisation, 7
Setting the temperature
Setting the spin speeds
Functions
Detergents and laundry, 8
Detergent dispenser
Preparing your laundry
Special items
Precautions and Advice, 9
General safety
Disposal
Saving energy and respecting the environment
Care and Maintenance, 10
Switching off the water or electricity supply
Cleaning your appliance
Cleaning the pump
Caring for your appliance door and drum
Checking the water inlet hose
Fuses
Changing the plug
Troubleshooting, 11
Service, 12
Before calling for assistance
Spare parts
GB
English
1
GB
A1637
A1437
A1237
!Packaging materials are not childrens toys.
Levelling
1. Install the machine on a flat sturdy floor, without
resting it up against walls, cabinets etc.
2. Compensate for any unevenness by tightening or
loosening the adjustable front feet. When adjusting
the feet, use a spirit level to check the machine
stands level, from side to side and from front to
back.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing
machine.
Water connection
Connecting the water inlet hose.
Remember that this is a cold-fill machine and the fill
hose fitted to the rear of the machine must be
connected to the cold water supply.
Before making the connections to the water outlet,
allow the water to run freely from the cold water
supply tap until it is perfectly clear.
Screw the cold water fill hose
onto the cold water supply tap
until tight.
Turn the tap on and check for leaks:
tighten if necessary.
!Make sure there are no kinks or bends in the hose.
!The water pressure at the tap must be within the values
indicated in the Technical details table (next page).
!If the water inlet hose is not long enough, contact a
specialist store or an authorised serviceman.
!Always use new hoses.
!Check the water hose at least once a year, replace
any that are cracked as worn hoses could split under
water pressure.
Installation
2
!Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction manual
accompanies the washing machine to inform the new
owner as to its operation and features.
!Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking
1. Unpack the machine.
2. Check whether the washing machine has been
damaged during transport. If this is the case, do
not install it and contact your retailer.
Remove the transit fixings
IMPORTANT: Follow these instructions to remove the
TWO transit fixings.
Situated one either side of the
rear panel, BOTH transit bolts
MUST be removed before use.
!Failure to do so may cause
damage to your machine.
It is important the transit bolt and
spacer ( ) come out intact.see pic
1. Unscrew the bolt using a
13mm spanner.
2. STOP when 3 threads can be
seen.
3. Hold, slide sideways and pull
to remove.
4. For safety, insert one of the
plastic covers (supplied with
your machine) over the hole.
!Repeat steps 1 to 4 to remove
the second transit bolt.
GB
The first wash cycle
Once the appliance has been installed and before you
use it for the first time, run a wash cycle without
detergent and no laundry, setting the 90˚C programme
without a pre-wash cycle.
Models A1637
A1437
A1237
59.5cm wide
Dimensions 85cm high
60cm deep
Capacity from 1 to 7kg Wash
Electric voltage 220/240 Volts 50Hz
connections maximum absorbed power:
1700W-2100W
Water maximum pressure 1 MPa (10 bar)
connections minimum pressure 0.05 MPa (0.5 bar)
drum capacity 54 litres
Spin Speed up to 1600 rpm - A1637
up to 1400 rpm - A1437
up to 1200 rpm - A1237
Control programme 3
programmes temperature 60˚C
according to - run with a 7kg load
IEC456
directive
This appliance is compliant with the
following European Community
Directives:
- 73/23/EEC & 93/68/EEC
(Low Voltage) and subsequent amendments.
- 89/336/EEC,92/31/EEC & 93/68/EEC
(Electromagnetic Compatibility) and subsequent
amendments.
Drainage connections
A. Connect the drain hose,
without kinking it, to a
draining duct or a wall
drain fixed at a height
between 65 and 100cm
from the floor.
B. Alternatively, place it
over the edge of a basin,
sink or tub, fastening the
hose supplied to the tap.
The free end of the hose
should not be under
water.
!We advise against the use of hose extensions. In
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150cm in length.
Electrical connections
Before plugging the appliance into the mains socket,
make sure that:
●The socket is earthed and in compliance with the
applicable law.
●The socket is able to sustain the appliances
maximum power load indicated in the Technical
Details table (on the right).
●The supply voltage is included within the values
indicated in the Technical Details table (on the right).
●The socket is compatible with the machines plug.
If this is not the case, replace the socket or the
plug.
!The machine should not be installed in an outdoor
environment, not even when the area is sheltered,
because it may be very dangerous to leave it exposed
to rain and thunderstorms.
!When the machine is installed, the mains socket
must be within easy reach and should be connected
to a suitable electrical supply.
!Do not use extensions or multiple sockets.
!The power supply cable must never be bent or
dangerously compressed.
!The power supply cable must only be replaced by
an authorised serviceman.
!The company denies all liability if and when these
norms are not respected.
3
Technical Details
Installation
A
B
GB

Specyfikacje produktu

Marka: Ariston Thermo
Kategoria: pralka
Model: A1637

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ariston Thermo A1637, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje pralka Ariston Thermo

Ariston Thermo

Ariston Thermo RSF 82 B AUS Instrukcja

30 Września 2024
Ariston Thermo

Ariston Thermo A1400SWD Instrukcja

22 Września 2024
Ariston Thermo

Ariston Thermo AVXXF137 Instrukcja

16 Września 2024
Ariston Thermo

Ariston Thermo CDE12X Instrukcja

15 Września 2024
Ariston Thermo

Ariston Thermo LI65EU Instrukcja

12 Września 2024
Ariston Thermo

Ariston Thermo AVTF129 Instrukcja

9 Września 2024
Ariston Thermo

Ariston Thermo RSF82BAUS Instrukcja

9 Września 2024
Ariston Thermo

Ariston Thermo AQXL 125 Instrukcja

9 Września 2024
Ariston Thermo

Ariston Thermo A1235 Instrukcja

9 Września 2024
Ariston Thermo

Ariston Thermo LBE129 Instrukcja

5 Września 2024

Instrukcje pralka

Najnowsze instrukcje dla pralka

Candy

Candy CS 15102D3-80 Instrukcja

15 Października 2024
GE

GE GSD3715FAA Instrukcja

15 Października 2024
Siemens

Siemens iQ700 WI14W540EU Instrukcja

15 Października 2024
LG

LG WTP22BK Instrukcja

15 Października 2024
Freggia

Freggia WTIE148 Instrukcja

15 Października 2024
Freggia

Freggia WISE126R Instrukcja

15 Października 2024
Freggia

Freggia WISE126B Instrukcja

15 Października 2024
Freggia

Freggia WISE126 Instrukcja

15 Października 2024
Freggia

Freggia WISA105 Instrukcja

15 Października 2024
Freggia

Freggia WISA106 Instrukcja

15 Października 2024