Instrukcja obsługi Ariston Thermo A1400WD

Ariston Thermo pralka A1400WD

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ariston Thermo A1400WD (16 stron) w kategorii pralka. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/16

Contents

WASHER DRYER

A1600WD

A1400SWD

A1400WD

A1200WD

Instruction booklet

Installation, 2-3

Unpacking

Remove the transit fixings

Levelling

Water connections

Drainage and electrical connections

Technical details

Washer dryer description, 4-5

Control panel

LEDs

Starting and programmes, 6-9

Briefly: how to start a programme

Programmes table

Setting the temperature

Setting the spin speeds

Functions

Drying section

Detergents and laundry, 10

Detergent dispenser

Preparing your laundry

Special items

Precautions and Advice, 11

General safety

Disposal

Saving energy and respecting the environment

Care and Maintenance, 12

Switching off the water or electricity supply

Cleaning

Caring for your appliance door and drum

Checking the water inlet hoses

Fuses

Changing the plug

Troubleshooting, 13-14

Service, 15

Before calling for assistance

Spare parts

English

! Packaging materials are not childrens toys.

Levelling

1. Install the machine on a flat sturdy floor, without

resting it up against walls, cabinets etc.

2. Compensate for any unevenness by tightening or

loosening the adjustable front feet. When adjusting

the feet, use a spirit level to check the machine

stands level, from side to side and from front to

back.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the machine.

Water connection

Connecting the water inlet hose.

Remember that this is a cold-fill machine and the fill

hose fitted to the rear of the machine must be

connected to the cold water supply.

Before making the connections to the water outlet,

allow the water to run freely from the cold water

supply tap until it is perfectly clear.

Screw the cold water fill hose

onto the cold water supply tap

until tight.

Turn the tap on and check for leaks:

tighten if necessary.

! Make sure there are no kinks or bends in the hose.

! The water pressure at the tap must be within the values

indicated in the Technical details table (next page).

! If the water inlet hose is not long enough, contact a

specialist store or an authorised serviceman.

! Always use new hoses.

! Check the water hose at least once a year, replace

any that are cracked as worn hoses could split under

water pressure.

Installation

GB ! Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction manual

accompanies the washer dryer to inform the new

owner as to its operation and features.

! Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking

1. Unpack the machine.

2. Check whether the washer dryer has been

damaged during transport. If this is the case, do not

install it and contact your retailer.

Remove the transit fixings

IMPORTANT: Follow these instructions to remove the

TWO transit fixings.

Situated one either side of the

rear panel, BOTH transit bolts

MUST be removed before use.

! Failure to do so may cause

damage to your machine.

It is important the transit bolt and

spacer ( ) come out intact.see pic

1. Unscrew the bolt using a

13mm spanner.

2. STOP when 3 threads can be

seen.

3. Hold, slide sideways and pull

to remove.

4. For safety, insert one of the

plastic covers (supplied with

your machine) over the hole.

! Repeat steps 1 to 4 to remove

the second transit bolt.

The first wash cycle

Once the appliance has been installed and before you

use it for the first time, run a wash cycle without

detergent and no laundry, setting the 90˚C

programme without a pre-wash cycle.

Models A1600WD, A1400SWD,

A1400WD, A1200WD

59.5cm wide

Dimensions 85cm high

60cm deep

Capacity from 1 to 6kg

Electric voltage 220/240 Volts 50Hz

connections maximum absorbed power:

1700W-2100W

Water maximum pressure 1 MPa (10 bar)

connections minimum pressure 0.05 MPa (0.5 bar)

drum capacity 53 litres

Spin Speed up to 1600 rpm - A1600WD

up to 1400 rpm - A1400SWD,

A1400WD

up to 1200 rpm - A1200WD

Control programme 3

programmes temperature 60˚C

according to

IEC50229 - dry run with a 1kg load followed by

directive a 5kg load for model A1600WD

- dry run with a 2kg load followed by

a 4kg load for models A1400SWD,

A1400WD and A1200WD

This appliance is compliant with the

following European Community

Directives:

- 72/23/CEE of 19/02/73

(Low Voltage) and subsequent amendments.

- 89/336/CEE of 03/05/89 (Electromagnetic

Compatibility) and subsequent amendments.

Drainage connections

A. Connect the drain

hose, without kinking it,

to a draining duct or a

wall drain fixed at a

height between 65 and

100cm from the floor.

Use the curved bracket,

if reqired.

B. Alternatively, place

it over the edge of a

basin, sink or tub,

fastening the hose

supplied to the tap.

! The free end of the hose should not be under water.

! We advise against the use of hose extensions. In

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150cm in length.

Electrical connections

Before plugging the appliance into the mains socket,

make sure that:

●the socket is earthed and in compliance with the

applicable law.

●the socket is able to sustain the appliances

maximum power load indicated in the Technical

Details table (on the right).

●the supply voltage is included within the values

indicated in the Technical Details table (on the

right).

●the socket is compatible with the machines plug.

If this is not the case, replace the socket or the

plug.

! The machine should not be installed in an outdoor

environment, not even when the area is sheltered,

because it may be very dangerous to leave it exposed

to rain and thunderstorms.

! When the machine is installed, the mains socket

must be within easy reach and should be connected

to a suitable electrical supply.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or dan-

gerously compressed.

! The power supply cable must only be replaced by

an authorised serviceman.

! The company denies all liability if and when these

norms are not respected.

Technical Details

Installation

Specyfikacje produktu

Marka:	Ariston Thermo
Kategoria:	pralka
Model:	A1400WD

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ariston Thermo A1400WD, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje pralka Ariston Thermo

Ariston Thermo RSF 82 B AUS Instrukcja

30 Września 2024

Ariston Thermo A1400SWD Instrukcja

22 Września 2024

Ariston Thermo AVXXF137 Instrukcja

16 Września 2024

Ariston Thermo CDE12X Instrukcja

15 Września 2024

Ariston Thermo LI65EU Instrukcja

12 Września 2024

Ariston Thermo AVTF129 Instrukcja

9 Września 2024

Ariston Thermo RSF82BAUS Instrukcja

9 Września 2024

Ariston Thermo AQXL 125 Instrukcja

9 Września 2024

Ariston Thermo A1235 Instrukcja

9 Września 2024

Ariston Thermo LBE129 Instrukcja

5 Września 2024

Instrukcje pralka

Najnowsze instrukcje dla pralka

Candy CS 15102D3-80 Instrukcja

15 Października 2024

GE GSD3715FAA Instrukcja

15 Października 2024

Siemens iQ700 WI14W540EU Instrukcja

15 Października 2024

LG WTP22BK Instrukcja

15 Października 2024

Freggia WTIE148 Instrukcja

15 Października 2024

Freggia WISE126R Instrukcja

15 Października 2024

Freggia WISE126B Instrukcja

15 Października 2024

Freggia WISE126 Instrukcja

15 Października 2024

Freggia WISA105 Instrukcja

15 Października 2024

Freggia WISA106 Instrukcja

15 Października 2024