Instrukcja obsługi Argon Sub 12

Argon głośnik Sub 12

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Argon Sub 12 (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
IMPORTANT SAFETY INSTRUCTIONS
Before using this subwoofer please read the
following instructions carefully observing all the
safety hints. Please keep this manual in a safe place
for future reference.
1/ Keep the power cords well protected IE do not
allow heavy objects to crush the cable or leave it
twisted as this may cause the cable to fray resulting
in electric shock. If you must use an extension cord
please try to keep the length to a minimum.
Common sense applies to all things electric and this
subwoofer is no different in this regard.
2/ Do keep this unit in a well ventilated place making
sure no drapes or other items are placed on top or near
the subwoofer as the amplifier can get quite warm
and indeed hot if the unit is not kept well ventilated.
Do not place any other objects on the subwoofer like
a vase because low frequencies generated by this
subwoofer can and will move anything placed on top
of the unit and can result in spilt water. This can
severely damage the unit and cause electric shock.
3/ If this unit requires servicing do not attempt to
repair it yourself always refer service to an authorized
Argon audio service centre. High voltages are located
within the cabinet which can result in serious injury
4/ Should you notice any malfunction including a
burning smell please switch the unit off, remove the
power plug from the wall and refer the unit to your
nearest Argon audio service centre.
5/ Argon audio subwoofers are designed to operate
on AC240V/50/60Hz power supply which is standard
in Europe. Do not attempt to operate on any other voltage.
1/ Power light
2/ Volume knob
3/ Frequency regulator knob
4/ Phase control knob
5/ High level inputs
6/ Line out
7/ Line in
8/ Power switch on/auto
9/ High level outputs
10/ Information on fuse replacement
11/ Power cable outlet (AC240V/50/60 Hz)
TO THE CUSTOMER:
Thank you very much for purchasing this
Argon audio subwoofer.
We have designed this product to be extremely easy
to operate but do read the instructions carefully to
maximize your long term enjoyment. Be sure not to
overload the speakers which can easily happen if the
volume is set too high. If you notice distortion please
turn the volume down quickly as permanent and
expensive damage can be caused by overloading
which is not covered by warranty. You can check this
out by going to our web page www.argonaudio.com.
Although your subwoofer comes with high level inputs
and outputs these are ideally only used for older amplifiers
or receivers which do not have the sub-out facility. If you
do have this facility then connect the subwoofer from sub-
out on the amp/receiver to either of the line inputs. In some
circumstances you will notice an improvement in the
subwoofers performance if you use a single line out to a
double line in from the amp/receiver to the subwoofer.
These connections are readily available from all hi-fi shops
of any note. The line output allows you to connect a second
subwoofer should you desire to do so. Simply run another
wire from the line outputs to the line input or line outputs of
the second subwoofer. If using a second subwoofer it is
recommended you have one either side of the room roughly
in line with the tower speakers and at least one metre clear
of a CRT television receiver.
Please note although this subwoofer is fitted with a
phase control it is highly unlikely you will need to adjust it.
Try with only the subwoofer operating rotating the knob
and settle on the setting which gives you more bass IE in
phase. The factory setting is correct in 99% of all cases.
Do avoid playing too long especially for extended periods
of time as this can cause damage to the amplifier and or the
speaker drive units or both.
Should you have any further queries please either contact
the retailer you purchased this unit from or us on
info@argonaudio.com
Once again thank you for purchasing a Argon audio
product and we trust you will have many years of trouble
free service.
FUNCTION
Output power 100w
Sensitivity 76db
Input sensitivity 440mv
Frequency response 40Hz-180Hz + - 3db
Power supply AC240V/50/60 Hz
HANDY HINTS
50/60Hz
AC240V/50/60Hz

Specyfikacje produktu

Marka: Argon
Kategoria: głośnik
Model: Sub 12

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Argon Sub 12, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Argon

Argon

Argon Fenris A55 Instrukcja

14 Września 2024
Argon

Argon Forte A55 MK2 Instrukcja

11 Września 2024
Argon

Argon Octave 4A Instrukcja

4 Lipca 2024
Argon

Argon Alto 55 Instrukcja

3 Lipca 2024
Argon

Argon Alto A4 Instrukcja

3 Lipca 2024
Argon

Argon FORTE A4 Instrukcja

3 Lipca 2024
Argon

Argon Octave 5 Instrukcja

3 Lipca 2024
Argon

Argon 6340A Instrukcja

2 Lipca 2024
Argon

Argon Bass 12 Instrukcja

2 Lipca 2024
Argon

Argon 6350 Instrukcja

2 Lipca 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024