Instrukcja obsługi Apart SB160

Apart odbiornik SB160

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Apart SB160 (4 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
SB-160
OWNER’S MANUAL
SOUNDBLOCKSOUNDBLOCK
• Read all documentation before operating your equipment.
Retain all documentation for future reference.
• Save the carton and packing material even if the equipment has arrived in good condition.
Should you ever need to ship the unit, use only the original factory packing.
• Do not spill water or other liquids into or on the unit.
• Make sure power outlets conform to the power requirements listed on the back of the unit.
• Do not use the unit if the electrical power cord is frayed or broken.
• Always operate the unit with the AC ground wire connected to the electrical system ground.
• Have gain controls on amplifiers turned down during power-up to prevent
speaker damage if there are high signal levels at the inputs.
• Do not connect the inputs / outputs of amplifiers or consoles to any other voltage source,
such as a battery, mains source, or power supply, regardless of whether
the amplifier or console is turned on or off.
• Power down & disconnect units from mains voltage before making connections.
• Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
• Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an
environment which may distort the normal flow of air around the unit. If the unit is used in an
extremely dusty or smoky environment, the unit should be periodically "blown free" of dust.
• Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages.
• Do not drive the inputs with a signal level greater than that required to drive equipment
to full output.
• Do not run the output of any amplifier back into another input.
• Do not ground the red output terminal, never connect a red output terminal to
another red output terminal.
• In case of mal-function this device should be serviced by qualified service personnel only.
SAFETY INFORMATION
!
!
!
!
!
C A U T I O N
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER OR BACK
NO USER-SERVICEABLE PARTS INSIDE
SERVICING ONLY FOR QUALIFIED PERSONNEL
1. Protection Led:
The Protection Led illuminates RED
when the amplifier is overheated or
when a shorted load or DC is
detected on the amplifier output.
The amplifier shall reset itself when
the problem is solved.
2. Signal LED indicator L & R
These LED’s will light up green when
the input detects audio signal.
3. Peak LED/limiter L & R
These red LED’s illuminates if the input signal of the amplifier is to high. Occasional blinking of these LED’s
is acceptable, but if it remains (on) or more than intermittently, then you should lower the input level or reduce the output
level of the preceeding component to avoid audible distortion.A built-in limiter will prevent excessive RMS clipping.
Remove Jp4 (Left channel) and Jp3 (Right channel) to de-activate this limiter function.
Please contact a qualified technician.
4. Level control L & R
These volume knobs are used to adjust the level of the outputs to the speakers.
5. Power switch
switch to 'ON' position to turn power on, and to 'OFF' to turn power off.
6. Monitor Jack
A stereo headphone can be inserted to this Jack for monitoring the amplifier output.
9. Unbalanced input cinch L & R
Cinch-RCA connectors for applying the input signal for the left and right channel.
10. Speaker output terminals connecting the speaker system
The minimum load is 4 ohms per channel. of course,
higher loads are acceptable.4 ohm=min. 4 pcs. of 16 ohm speakers wired
in parallel or max. 2 pcs. of 8 ohm speakers wired in parallel.
Please note that 2 pcs. of 6 ohm speakers wired in parallel are NOT allowed.
11. AC outlet un-switched)/AC input
Use AC cord connect to the AC input to a AC socket.
Use the AC outlet to power other modules (with the MB-AC link cable) or to other associated equipment.
AC voltage is always present as long as the amplifier is connected to the AC voltage source.
12. AC fuse
It the fuse is blown, please disconnect the power cord, and replace fuse by the same value 3.15 AT
of the SLOW BLOW type. If the fuse blows again, then contact your dealer for further servicing.
13. Mono - Stereo switch
Mono Stereo switch for the input signal.
14. Low cut filter
Switches on a high pass filter of 100Hz. This features can be used for driving small or horn speakers.
10
9
11
12
13
12
3
4
6
5
SOUNDBLOCK SOUNDBLOCK
14
NOT ALLOWED
2 X 80 / 120 Watt
2 X 60 / 90 Watt
0.775 Vrms/MAX input level +14dBV
20 Kohm
15hz - 30KHz
<0.03%
(4 ohm) >400
300 VA MAX
70 X 140 X 335 MM
Net. 2.8 Kg
Power Rated / Max
2 ohm
4 ohm
8 ohm
Input Sensitivity
Input impedance
Freq. Response
Total harm. distortion
Damping factor
Power consumption
Dimensions (H x W x D):
Weight
Technical specifications SBR160
• Due to the built-in limiter, some values may differ from the specs listed above.
Due to our continuous research and development, the product specifications may
change without prior notice at any time.
• The turning speed of the cooling fan is related to the temperature of the amplifier.
When the amplifier is cold it’s normal that the fan doesn’t turn.
Only if a lot of output-power is requested the fan will turn.
• A built-in limiter will prevent excessive RMS clipping.
Remove Jp4 (Left channel) and Jp3 (Right channel) to de-activate this limiter function.
• If ‘Hum’ or Buzz’ occurs when connecting different inputs, then this is often caused by
‘GROUND or EARTH LOOPS’.
Inside you can disconnect Jp5 to break this ground loop.
Please contact a qualified technician to do this.
SPECIAL FEATURES
SPECIFICATIONS

Specyfikacje produktu

Marka: Apart
Kategoria: odbiornik
Model: SB160

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Apart SB160, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Apart

Apart

Apart SBR160 Instrukcja

14 Października 2024
Apart

Apart CHAMP-ONE-SLV Instrukcja

4 Września 2024
Apart

Apart SB160 Instrukcja

22 Sierpnia 2024
Apart

Apart CHAMP-4 Instrukcja

16 Sierpnia 2024
Apart

Apart PA2240BP Instrukcja

4 Lipca 2024
Apart

Apart REVAMP4100 Instrukcja

4 Lipca 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Denon

Denon AVR-S900W Instrukcja

15 Października 2024
Pro-Ject

Pro-Ject Amp Box DS2 Instrukcja

15 Października 2024
AKG

AKG HP12U Instrukcja

15 Października 2024
American Audio

American Audio VLP 600 Instrukcja

14 Października 2024
Chord

Chord Anni Instrukcja

14 Października 2024
Sennheiser

Sennheiser EM 9046 SU Instrukcja

14 Października 2024
Yamaha

Yamaha MusicCast RX-V481 Instrukcja

13 Października 2024
JL Audio

JL Audio VX600/6i Instrukcja

12 Października 2024
Pioneer

Pioneer SX-303RDS Instrukcja

10 Października 2024
Denon

Denon AVR-991 Instrukcja

10 Października 2024