Instrukcja obsługi Apart CMX20DT

Apart głośnik CMX20DT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Apart CMX20DT (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
CMX20DT CM design loudspeaker
Safety precaution
• Keep this manual for future reference.
• When cutting the mounting hole for the speaker, make sure there is sufficient clearance behind the
panel (no obstructions like A/C channels, power lines etc).
• Take care of your speaker wires, they should be free of damage. Damaged speaker wires might result in
poor sound quality and can damage amplifiers.
• Only use accessories specified by the manufacturer
• Make sure the mounting panel can support the speakers weight.
• Use sufficient amount of speakers to avoid dead spots.
• No mains power shall be connected to the loudspeakers, doing so will damage the speaker.
• This apparatus should only be serviced by qualified personnel. If not warranty might be void.
• Use cable of the right gauge, certainly for long runs.
• Use cables with clear color indication and maintain polarity throughout the whole system.
• Avoid loud feedback from microphones, this can damage your speaker.
• Please check the units condition after unpacking. If the outside of the carton box has been damaged,
inform your shipper immediately.
Warranty info
Warranty claims and claims for hidden defects can
be considered only if the defects appear within the
warranty period of 24 months and are notified within
8 days following their appearance per registered letter.
The warranty is not valid in case of an incident, wear,
for moving parts, power surges, inadequate packing
or shipping, improper use or storage and the disregard
of recommendations of Audioprof. The warranty only
concerns the spare parts and not the involved labor,
transportation or any other costs. The product must
be returned in the original packaging with the proof
of purchase by an Audioprof authorized reseller.
CMX20DT
The Apart CMX20DT is a 2-way 100V / 70V / 16 ohm built-in design ceiling loudspeaker. The
loudspeaker has a 8” woofer, a 1” coaxial tweeter and a high quality 100 / 70 volt speaker line
transformer with multiple power taps. CMX20DT is the perfect choice for the distribution of
microphone calls and background music. The mounting frame is made of high quality ABS. The
steel grille is kept in place by strong magnets.
The general terms and conditions can be found here:
http://www.apart-audio.com/conditions/General_Terms_and_Conditions_Apart_Audio.pdf
WWW.APART-AUDIO.COM
The loudspeaker is easy to install, due to its simple mounting system.
(1) Use the cutout template to mark the mounting hole.
(2) When making the hole in your mounting panel, double check if there are no cables
or any other obstructions behind the mounting panel. Cutting the mounting panel
without this check might result in damaged infrastructure or power lines. Please make
sure that the mounting structure is capable of safely supporting the speaker’s weight.
(3) Remove the speaker grille.
(4) Turn the dog-ears inwards and tighten the dog-ear screws slightly to make them stay
in the inward position.
(5) Connect the speaker wires and insert the speaker in the precut speaker opening.
(6) Fasten the dog-ear screws carefully until the speaker sits safely in place. Do not
overtighten the dog-ear screws!
(7) The speaker grille is held in place by powerful magnets.
NOTE: for use in low impedance systems, always disconnect the 100 / 70 volt
transformer and connect the low impedance loudspeaker wires directly at the
loudspeaker.
Mounting the loudspeaker
1
2
3
6
4
7
5
WWW.APART-AUDIO.COM
*2.5 W: 70 volt only
outside diameter 250 mm
depth 87 mm
cutout 223 mm
loudspeaker system 2-way
woofer size 8 inch
woofer cone material polypropylene
tweeter size 1 inch
100 V / 70 V power taps 20 - 10 - 5 - 2.5* watts
mounting system 3 screws
impedance 16 ohms
low impedance dynamic power 100 watts
SPL 1W/1m 88 dB
max SPL 1m 108 dB
frequency response 50 - 20K Hz
main construction material ABS plastic
grille main material steel
IP rating 50
applicable low impedance yes
applicable in 100 V / 70 V yes
dispersion angle (1000 Hz) 180°
min / max ceiling thickness 3 - 27 mm

Specyfikacje produktu

Marka: Apart
Kategoria: głośnik
Model: CMX20DT

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Apart CMX20DT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Apart

Apart

Apart CM5EH Instrukcja

3 Października 2024
Apart

Apart OVO5 Instrukcja

2 Października 2024
Apart

Apart CMX20DT Instrukcja

13 Września 2024
Apart

Apart COLS101 Instrukcja

7 Września 2024
Apart

Apart CMX20T Instrukcja

4 Września 2024
Apart

Apart CM1008-BL Instrukcja

28 Sierpnia 2024
Apart

Apart CMR15T Instrukcja

27 Sierpnia 2024
Apart

Apart MASK6-BL Instrukcja

24 Sierpnia 2024
Apart

Apart CM6SF Instrukcja

23 Sierpnia 2024
Apart

Apart H10-G Instrukcja

21 Sierpnia 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024