Instrukcja obsługi AMX NXD-700i

AMX monitor NXD-700i

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AMX NXD-700i (2 stron) w kategorii monitor. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Installation Guide

NXD-700i 7”Modero® Wall/Flush Mount Touch Panel with Intercom

Overview

The NXD-700i (FG2258-10) is an incredibly versatile user interface, combining a sleek,

compact size, Wall/Flush Mount flexibility and the ability to create a high quality digital home/

office intercom network or to make/receive digital local, long distance and international

telephone calls.

Simply add the AMX SIP Communications Gateway (FG2182-0x) for calls that sound

incredibly clear.

ATTENTION!

Verify you are using the latest NetLinx Master and Modero touch panel firmware (available

from www.amx.com). Verify the TPDesign4 program being used is Version 2.6 or higher, and

download the latest G4 Support Files from www.amx.com.

Specifications

Installing the NXD-700i

Consult the NXD-700i Touch Panels Operation/Reference Guide for the various supported

installation methods and dimensions.

Panel Connectors

FIG. 2 shows the connectors located on the NXD-700i:

• The mini-USB port is used both for programming the touch panel and for audio output.

• The mini-USB port automatically detects the presence of a headphone adaptor,

allowing the port to be used for headphone connectivity.

Note: For more information on connection and use of the Panel Connectors, as well as

information on programming and headphone connectivity, please refer to the NXD-700i

Operation/Reference Guide, available at www.amx.com.

FIG. 1 NXD-700i (shown with Trim Ring 60-2258-26)

NXD-700i Specifications

Dimensions (HWD):

NXD-700i

(Faceplate included)

5.93" x 7.87" x 3.28" (15.06 cm x 20.00 cm x 8.33 cm)

CB-TP7 (optional

Rough-In Box)

5.47" x 7.23" x 3.40" (13.90 cm x 18.40 cm x 8.64 cm)

Power Requirements • PoE Powered - No local power supply needed

• Max power draw: 5.5W

Memory: • 128 MB SDRAM

• 256MB integrated Flash Memory (not upgradeable - factory

programmed)

Weight: 1lb (0.45kg)

Panel LCD

Parameters:

• Aspect ratio: 16 x 9

• Brightness (luminance): 300 cd/m2

• Contrast ratio: 400:1

• Display colors: 256 thousand colors (18-bit color depth)

• Dot/pixel pitch: 0.19 mm

• Panel type: TFT Color Active-Matrix

• Screen Resolution: 800 x 480 pixels (HV) @ 60 Hz frame frequency

Active Screen Area: 6.00" x 3.60" (15.24cm x 9.14cm)

Viewing Angle: Up/Down/Left/Right: 70/60/70/70

IR Reception Angle: • Horizontal: + 50° (left and right from center)

• Vertical: + 30° (up and down from center)

Supported Audio

Sample Rates

48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz, 12000Hz,

11025Hz, and 8000Hz

Intercom Full duplex VoIP capabilities

Video Capabilities: Supports DynaMo™ (M-JPEG), including DynaMo Resource (enhanced

M-JPEG) Images. Refer to the TPDesign4 online help and NXD-700i /

NXT-CA7 Operation/Reference Guide for details on configuring DynaMo

and DynaMo Resource Images.

Front Panel: • Light Sensor: Photosensitive light detector for automatic adjustment

of the panel brightness

• Motion Sensor (PIR): Proximity Infrared Detector to wake the panel

when panel is approached

• Front Bezel Button: Provides both access to the setup and calibration

pages and toggles the panel between “sleep” or “wake” state. This

button is also user-programmable.

• Microphone: Frequency response of 300 to 3400Hz; used for

intercom applications.

• Speaker: Output of 4Ohm, 2 Watt, with a 300Hz low cutoff frequency

Programmable pushbutton/LED

Microphone

Sleep / Setup Access button

Speaker

Programmable pushbutton/LED

Note: Programmable pushbutton/LEDs available only on Trim Ring 60-2258-26

Trim Ring

NXD-700i Specifications (Cont.)

Side Panel Connectors • Ethernet 10/100 Port: RJ-45 port for 10/100 Mbps communication.

The Ethernet port automatically negotiates the connection speed

(10 Mbps or 100 Mbps), and whether to use half duplex or full duplex

mode.

Power is supplied through Power Over Ethernet (PoE).

NXD-700i panels communicate with the NetLinx Master using the

ICSP protocol over Ethernet.

LEDs show communication activity, connections, speeds, and mode

information:

• L/A- link /activity - Yellow LED lights On when Ethernet cables are

connected and terminated correctly and then blinks when receiving

Ethernet data packets.

• SPD-speed - Green LED lights On when the connection is 100 Mbps

and turns off when the speed is 10 Mbps.

• Mini-USB Connector: 5-pin Mini-USB connector used for

programming, firmware update, and touch panel file transfer between

the PC and the target panel.

The connector is also used for providing audio output for external

speakers.

Operating /Storage

Environments:

• Operating Temperature: 0° C (32° F) to 40° C (104° F)

• Operating Humidity: 20% - 85% RH

• Storage Temperature: -20° C (-4° F) to 60° C (140° F)

• Storage Humidity: 5% - 85% RH

Certifications: • FCC Part 15 Class B and CE

• IEC60950

• RoHS

Included

Accessories:

• Installation Kit for NXD-700i panels (KA2258-02):

- 4 Phillips-head screws (#4-40 x 0.250 Black) (80-0112)

- 3 Drywall clips (62-5924-05)

- 3 #6 sheet metal screws (80-0192)

• Trim Ring with button openings (60-2258-26)

• Trim Ring without button openings (60-2258-25)

Other AMX Equipment: • NXA-RK7 Rack Mount Kit (FG2904-53)

• CB-TP7 Rough-In Box (FG035-10)

• PS-POE-AF PoE Injector (FG423-80)

• CC-USB Type-A to Mini-B5-wire programming cable (FG10-5965)

• USB to Headphone Adaptor (FG5966-23)

• AMX SIP Communications Gateway (FG2182-0x)

FIG. 2 Connector layout on the NXD-700i

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

12/11

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-2258-10 REV: B

Ethernet/RJ-45 Port: Connections and Wiring

FIG. 3 describes the blink activity for the Ethernet 10/100 Base-T RJ-45 connector and cable.

The Ethernet cable is connected to the rear of Table Top and side of the Wall Mount panels.

Modero Setup and System Connection

The panel is equipped with setup pages that allow you to set and configure various features

on the panel. Consult the NXD-700i Touch Panels Operation/Reference Guide for detailed

information on the Setup pages.

Accessing the Setup and Protected Setup Pages

1. Press the grey Front Setup Access button for 3 or 6 seconds to open the Setup page.

2. Press the Protected Setup button.

This invokes a keypad for entry of the password to allow access to the Protected Setup

page.

Enter 1988 (the default password), and press Done to proceed.

Note: Clearing Password #5, from the initial Password Setup page, removes the need for

you to enter the default password before accessing the Protected Setup page.

Setting the Panel’s Device Number

In the Protected Setup page:

1. Press the field to open the Device Number keypad.Device Number

Enter a unique Device Number assignment for the panel and press ,Done to return to

the Protected Setup page.

2. Press Reboot to reboot the panel, and apply the new Device Number.

Master Connection

The panel requires you to establish the connection between it and your master. In the

Protected Setup page:

1. Select System Settings

2. When using Ethernet, press the listed Mode to toggle through the available connection

modes:

3. Select the Master Port Number to open the keypad and change this value. The default

setting for the port is 1319.

4. Set your Master Port and select Done.

If you have enabled password security on your master you need to set the username

and password within the device.

a. Select the blank field Username to open the keyboard.

b. Set your Username and select Done.

c. Select the blank field Password to open the keyboard.

d. Set your Password and select Done.

5. Press the button to return to the Back Protected Setup page.

6. Press the button to reboot device and confirm changes.Reboot

Panel Intercom Configuration

Incorporating an Intercom Capable Panel Into Your NetLinx System

Download the module for the intercom panel from www.amx.com, and include it in your

NetLinx project file.

For searching purposes, the module manufacturer is AMX and the model is Intercom.

Advanced Setup

The intercom’s advanced setup pages are accessed through the intercom setup pages. The

advanced pages allow you to set the panel intercom to be monitored, to monitor other

intercom panels, and to name the panel. It is important to name the intercom panel, the name

is displayed in other panels’ intercom call directory pages.

Consult the NXD-700i Touch Panels Operation/Reference Guide for more intercom setup

features.

1. Select the button on your intercom page.Setup

2. On the intercom setup page, press Advanced Setup. This launches the password

numeric keypad.

3. Enter the password and press Done. The default password is Password 4 of the

panel’s firmware Password Setup.

Naming the Panel

In the intercom Advanced Setup page:

1. Press in the area under . This launches an on screen keyboard.Panel Name

2. Type the name of the panel and press Done. This is the name that is displayed in

other panels’ intercom call directory pages.

3. Press Back to return to the intercom setup pages.

4. Press Exit when you are finished.

Note: The Panel Name is also the G4 Web Control Name and can be set via the panel’s

firmware pages.

Calibrating the Panel

Peel the protective plastic film from the LCD.

Note: If the protective plastic film on the LCD is not removed, the panel may not respond

properly to touch points on the LCD nor allow proper screen calibration.

1. Press and hold the grey Front Setup Access button (see FIG. 1) for 6 seconds to

pass-over the Setup page and access the Calibration setup page.

2. Press the crosshairs (on the Calibration page) to set the calibration points on the LCD

3. After the "Calibration Successful.." message appears, press anywhere on the screen

to continue and return to the Setup page.

Additional Documentation

For more detailed installation, configuration, programming, file transfer, and operating

instructions, refer to the NXD-700i Touch Panels Operation/Reference Guide, available on-

line at www.amx.com.

Specyfikacje produktu

Marka:	AMX
Kategoria:	monitor
Model:	NXD-700i
Kolor produktu:	Czarny
Wbudowane głośniki:	Tak
Certyfikaty:	FCC 15 B, CE, IEC 60950, RoHS\r\n
Długość przekątnej ekranu:	7 "
Ilość portów Ethernet LAN (RJ-45):	1
Zakres temperatur (eksploatacja):	0 - 40 °C
Zakres wilgotności względnej:	20 - 85 %
Rozdzielczość:	800 x 480 px
Współczynnik kontrastu (typowy):	400:1
Ekran dotykowy:	Tak
Pobór mocy:	5.5 W
Zakres temperatur (przechowywanie):	-20 - 60 °C
Dopuszczalna wilgotność względna:	5 - 85 %
Wymiary produktu (SxGxW):	200 x 83.3 x 150.6 mm
Kształt ekranu:	Płaski
Rozmiar plamki:	0.19 x 0.19 mm
NVIDIA G-SYNC:	Nie
AMD FreeSync:	Nie
Waga (bez podstawy):	450 g
Jasność:	300 cd/m²
Montaż naścienny / rzutowanie na sufit:	Tak
Format obrazu:	16:9
Część widoczna ekranu:	152.4 x 91.4 mm
Ilość portów upstream:	1