Instrukcja obsługi AMX MXT-700

AMX monitor MXT-700

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AMX MXT-700 (2 stron) w kategorii monitor. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Installation Guide

MXT-700 7" Modero X® Series Tabletop Touch Panel

Overview

The MXT-700 7” Modero X® Series Tabletop Touch Panel (FG5968-04) provides

several industry firsts, including a beautiful, capacitive multi-touch screen that

provides users access to multiple applications with minimal navigation. The Modero X

Series is the most elegant family of interfaces designed specifically for dedicated room

control. This new generation of touch panels is built for usability offering edge-to-edge

capacitive touch glass with multi-touch capabilities. It features advanced technology

empowering users to operate AV equipment seamlessly, while providing the ultimate

in audio and video quality. The distinctive appearance will complement even the most

sophisticated meeting facilities and homes. With a lightning fast processor, brilliant

graphics and enhanced capabilities, the Modero X Series is the control surface that

simply delivers more.

For more information on installation and configuration, please refer to the

MXT/MXD-700 Operation Reference Guide, available at www.amx.com.

Common Application

The MXT-700 is intended for boardrooms, conference rooms, or auditoriums where a

panoramic control surface is needed to provide access to multiple functions

simultaneously while remaining elegantly unobtrusive. In residences, it is perfect for

kitchens, home theaters, or home offices where the panoramic control surface can be

used to manage systems throughout the house.

Product Specifications

NOTE: The MXT-700-NC (FG5968-27) No Comm touch panel does not have camera

or microphone capability. It otherwise has all of the functionality of the MXT-700 panel.

FIG. 1 MXT-700

MXT-700 (FG5968-04) Specifications

Power: PoE (Power over Ethernet), 802.3af, class 3

Power Consumption: • Full-On: 8W maximum

•Standby: 3.2 W

•Shutdown: 1 W

•Startup Inrush Current: Not Applicable due to PoE standard

Front Panel Components:

NFC Transceiver: Antenna and transceiver for Near Field Communications

device detection and interaction.

Light Sensor: Photosensitive light detector for automatic adjustment of the

panel brightness.

Motion Sensor: Proximity detector to wake the panel when it is approached.

• Typical Range: 1 foot (30.48 cm)

•Maximum Range: 3 feet (91.44 cm)

•Range width: 10 degrees

Sleep Button: Single button on top of panel for placing panel in sleep mode,

for powering off the panel, and for accessing the Settings

Pages.

Microphone: -42dB ± 3dB sensitivity FET microphone

Speakers: 4 ohm, 2 Watt, 300Hz cutoff frequency

Rear Panel Components:

USB connections: 2 easily accessible USB ports on rear of base, used for

connection to keyboard, mouse, or other peripherals.

Ethernet 10/100 Port

and Cable:

10/100 port, RJ-45 connector through cable extension for

Ethernet connectivity and PoE.

Touch Panel Display:

Display Type: TFT Active Matrix Color LCD with In-Plane Switching (IPS)

technology.

Display Size: 7.3" x 4.8" (186 mm x 122 mm), 8.8" (222 mm) diagonal

Viewable Area: 6.05" x 3.54" (154 mm x 90 mm), 7.0" (178 mm) diagonal

Sleep Button

Front Side

Proximity

Sensor

NFC Sensor

MXT-700 (FG5968-04) Specifications (Cont.)

Touch Panel Display (Cont.):

Viewing Angle: • Vertical: ± 89°

• Horizontal: ± 89°

Screen Resolution

(W x H):

1024x600

Aspect Ratio (W x H): 16x9

Brightness: 400 cd/m2

Contrast Ratio: 800:1

Color Depth: 16,7M colors

Backlight Type: LED

Touch Overlay: Projected Capacitive; Multi-touch support, 3 simultaneous

max.

Communications:

Ethernet: 10/100 port, RJ-45 connector. Supported IP and IP-based

protocols: UCP, TCP, ICMP, ICSP, IGMP,DHCP, Telnet, FTP,

DNS, RFB (for VNC), HTTP

USB: 2 - USB host 2.0, Type A ports

Near Field

Communications

(NFC):

Supports standards ISO/IEC 15693, ISO/IEC 14443A, ISO/

IEC 14443B; Unique Identifier (UID), Typ Range=.25”,

Max = .5"

Bluetooth: HID Profile v1.1, Keyboard/Mouse Support, requires MXA-BT

Bluetooth Adaptor

Video:

Supported Video

Codecs:

• MPEG2-TS: MPEG-2 Main Profile @High Level up to 720p

at 25 fps (decode only)

• MJPEG up to 720p at 25 fps (decode only)

Streaming/File Formats: MPEG-TS for MPEG-2; HTTP for MJPEG

Audio:

Streaming/File Formats: WAV, MP3 (as part of touch panel file only - no USB storage)

Intercom: Full Duplex VoIP, SIP v2.0 (supported with AMX-CSG)

Operating Environment: • Operating Temperature: 32° F to 104° F (0° C to 40° C)

• Storage Temperature: 4° F to 140° F (-20° C to 60° C)

• Humidity Operating: 20% to 85% RH

• Humidity Storage: 5% to 85% RH

Dimensions (HWD): 5" x 7 5/16” x 4 1/8” (126 mm x 187 mm x 105 mm)

Weight: 1.8 lbs (0.82 kg)

Certifications: • FCC Part 15 Class B

• C-Tick CISPR 22 Class B

• CE EN 55022 Class B and EN 55024

• CB Scheme IEC 60950-1

• IC

• IEC/EN-60950

• RoHS

Included Accessories: • MXT-700 Installation Guide (93-5968-04)

• MXA-USB-C, USB Port Cover Kit, Modero X Series Touch

Panel (FG5968-18)

• HPG-10 .75-inch HydraPort .75-IN. Grommet (FG570-01)

• MXA-CLK, Modero X Series Cleaning Kit (FG5968-16)

Other AMX Equipment: • PS-POE-AT, High-Power PoE Injector (FG423-81)

• PS-POE-AF-TC, POE Injector, 802.3af Compliant

( )FG423-83

• MXA-BT Bluetooth USB Adaptor (FG5968-19)

• NXA-ENET8POE, Gigabit PoE Ethernet Switch

( )FG2178-62

• NXA-ENET8-2POE, Gigabit Switch, 8 Port POE, 2 Port

SFP (FG2178-63)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

7/12

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-5968-04 REV: D

Panel Connectors and Wiring

Any USB peripherals (mouse, keyboard, etc.) may be connected to one of the two

USB ports on the rear of the device (FIG. 2). Updates to the device’s firmware are also

made via the USB ports.

Power via Power Over Ethernet

Power for the MXT-700 is supplied via Power Over Ethernet (PoE), utilizing an AMX-

certified, capacitive touch-compliant PoE injector such as the PS-POE-AT High Power

PoE Injector (FG423-81) or equivalent PoE device. If using a PoE injector, the PoE

injector should be installed between the MXT-700 and the incoming Ethernet cable,

and connected to the RJ45 port on the cable attached to the device (FIG. 3) .

Ethernet Cable Installation and Modification

In installations where you wish to conceal the Ethernet cable, a hole at least 1.00”

(2.54 cm) in diameter is required in the surface to allow passage of the female RJ45

connector (FIG. 3). If using a smaller hole is unavoidable, you will need to disconnect

the Ethernet cable (ECA5968-05) from the device.

NOTE: The minimum diameter hole through which the Ethernet cable may pass is

0.50" (1.27 cm).

To disconnect and reconnect the MXT-700’s Ethernet cable to allow use of a hole

smaller than 1.00” in diameter:

1. On a soft surface, turn the MXT-700 face-down to access the bottom of the

device.

2. Remove the clamp holding the Ethernet cable (FIG. 4) until the Ethernet cable

moves freely.

3. Remove the Ethernet cable connector and pull the cable out of the clamp.

4. Pass the Ethernet cable (ECA5968-05) through the hole, with the RJ45

connector on the other side of the installation surface from the device.

5. Press the Ethernet cable back into the clamp. Do NOT tighten the clamp at this

time.

6. Using a nonconductive item such as a wooden stick, reinsert the Ethernet cable

connector into the device. Use the stick to ensure that the connector is properly

seated.

7. Tighten the clamp to secure the Ethernet cable. Make sure the clamp is around

the bundled black cable, not the individual wires.

8. Connect the RJ45 connector to its incoming Ethernet cable and apply power.

Configuring the MXT-700

The MXT-700 is equipped with Settings Pages that allow you to set and configure

various features on the panel. For more information on connecting and configuring the

MXT-700 to a network, please refer to the Modero X Series Programming Guide,

available at www.amx.com.

Accessing the Settings Pages

To access the Settings Pages on the MXT-700, press and hold the Sleep Button

(FIG. 1) on the top of the panel for 3 seconds. The user will be prompted to release the

button to enter the Settings page.

Accessing the Configuration Page

1. From the Settings Page, select Configuration. If the Configuration page is

password protected, this opens a password keypad.

2. Enter the panel password into the keypad (the default is 1988) and select OK to

access the page.

Setting the Panel’s Device Number and Device Name

In the Configuration page:

1. Press Panel to open the Panel Configuration page.

2. Ensure that the Synchronize Device Names button is not selected, and click it to

deselect it if it is.

3. Press Device Number to open the Device Number keypad.

4. Enter a unique Device Number assignment for the panel and press OK.

5. Press the Device Name field to open the Device Name keypad.

6. Enter a unique Device Name assignment for the panel and press OK.

7. Click the arrow on the top left of the page once to return to the Configuration

page and twice to return to the Settings page.

Accessing the Connection & Networks Page

1. From the Settings Page, select Connection & Networks. If the page is password

protected, this opens a password keypad.

2. Enter the panel password into the keypad (the default is 1988) and select OK to

access the page.

Connecting to a Master

The panel requires that you establish the type of connection you want to make

between it and your Master.

In the Connection & Networks page:

1. Select Master Connection to open the Master Connection page

2. Press Mode to toggle through the available connection modes:

3. If you have enabled password security on your Master, you need to set the user-

name and password within the device.

a. Select Username to open the Master User keyboard.

b. Set your Username and select OK.

c. Select the Password to open the Master Password keyboard.

d. Set your Master Password and select OK.

e. Press the Back button twice to return to the Settings page.

Configuring the Panel to a Network

The first step is to configure the panel’s communication parameters. This only

configures the panel to communicate with a network, and it is still necessary to tell the

panel with which Master it should be communicating.

Network Communication With a DHCP Address

In the Connection & Networks page:

1. Select Network Connection to open the Network Connection page.

2. Toggle the DHCP/Static field until the choice cycles to DHCP. This action causes

all fields on the page (other than Host Name) to be greyed-out.

3. Select Host Name to open the Host Name keyboard. Enter the new host name

and click OK.

FIG. 2 Connectors on the rear of the MXT-700

FIG. 3 Back of the MXT-700, showing RJ45 port and cable for PoE

FIG. 4 Bottom of the MXT-700

USB Ports Entry for RJ45/

PoE Cable

Speaker

Cable length

edited for clarity

RJ45 Port

Ethernet Cable

Connector

Clamp

MXT-700

Connection Modes

Mode Description Procedures

Auto The device connects to the first

master that responds.

This setting requires that you set

the System Number.

Setting the System Number:

1. Select Master System Number to open

the keypad.

2. Set your Master System Number and

select OK.

URL The device connects to the

specific IP of a master via a TCP

connection.

This setting requires that you set

the Master’s IP.

Setting the Master IP:

1. Select the Master IP number to the

keyboard.

2. Set your Master IP and select OK.

Listen The device “listens” for the

Master to initiate contact.

This setting requires you provide

the master with the device’s IP.

Confirm device IP is on the Master URL list.

You can set the Host Name on the device

and use it to locate the device on the master.

Host Name is particularly useful in the DHCP

scenario where the IP address can change.

Specyfikacje produktu

Marka:	AMX
Kategoria:	monitor
Model:	MXT-700
Wbudowane głośniki:	Tak
Moc wyjściowa (RMS):	2 W
Długość przekątnej ekranu:	7 "
Pojemność pamięci wewnętrznej:	512 MB
Zakres temperatur (eksploatacja):	0 - 40 °C
Zakres wilgotności względnej:	20 - 85 %
Rozdzielczość:	1024 x 600 px
Współczynnik kontrastu (typowy):	800:1
Natywne proporcje obrazu:	16:9
Typ ekranu dotykowego:	Przeznaczony dla wielu użytkowników
Ekran dotykowy:	Tak
Pobór mocy w trybie czuwania:	3.2 W
Pobór mocy:	8 W
Zakres temperatur (przechowywanie):	-20 - 60 °C
Dopuszczalna wilgotność względna:	5 - 85 %
Maksymalna temperatura termometru zwilżonego (wet bulb temp.) Podczas eksploatacji (w °f):	32 - 104 °F
Wymiary produktu (SxGxW):	187 x 105 x 126 mm
Technologia wyświetlacza:	LCD
Typ podświetlacza:	LED
Kształt ekranu:	Płaski
Kąt widzenia (poziomy):	89 °
Kąt widzenia (pionowy):	89 °
Kolory wyświetlacza:	16.78 millionów kolorów
NVIDIA G-SYNC:	Nie
AMD FreeSync:	Nie
Waga (bez podstawy):	820 g
Jasność:	400 cd/m²
Format obrazu:	16:9
Część widoczna ekranu:	90 x 154 mm
Zintegrowany aparat fotograficzny:	Nie
Technologia touchscreen:	Pojemnościowy