Instrukcja obsługi AMX FG1010-330-WH

AMX nieskategoryzowany FG1010-330-WH

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AMX FG1010-330-WH (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

QUICK START GUIDE

DXLink Twisted Pair 4K Transmitters and Receivers

Overview

The DXLink 4K HDMI Decor Style Wallplate Transmitter and DXLink 4K HDMI Receiver

Module transmit HDMI Video and Audio over twisted pair cable. DXLink Twisted Pair 4K

endpoints can be set up in one of three ways:

• Endpoint Mode (Switcher) – connect one or more to a switcher with an integrated

Master.

• Endpoint Mode (Standalone) – connect TX/RX pair directly to each other with RX

connected to a NetLinx Central Controller via LAN or directly to Controller.

• Extender Mode (Standalone) – connect TX/RX pair directly to each other.

NOTE: DXLink Twisted Pair 4K Receiver modules can also be setup for standalone

communication with Solecis 4K Digital Switchers.

DXLink 4K HDMI Receivers support InstaGate Pro® and SmartScale® Technology. The

Hardware Reference Manual – DXLink Twisted Pair 4K Transmitters and Receivers

contains complete documentation (including full specifications and supported input

and output resolutions); for details, see www.amx.com .

System Setup

The TX and RX work with a switcher that supports DXLink Technology for transmission

of HDMI (or with a Central Controller) or as a standalone pair. The Transmitter receives

an HDMI signal and embedded audio from the source. Both the video and embedded

audio are transported over twisted pair cable to a DXLink Twisted Pair 4K Input Board

(or connector). The signal is routed via the DXLink Twisted Pair 4K Output Board (or

connector) to an RX. The RX also provides a stereo audio output.

Wallplate Transmitter Mounting

The 4K HDMI Wallplate TX mounts in a standard US single-gang back box. Standard

decor style cover plates are customer provided to allow matching the individual decor of

an environment or matching other standard decor covers in a room/area.

Receiver Mounting Options (Rack Trays and Mounting Brackets)

For details on the four versatile mounting kit options for V Style modules (rack tray, rack

tray with fill plates, surface mount, and pole mount), see www.amx.com .

IMPORTANT: When mounting under a surface, the module should be mounted upright

and lowered in the mounting bracket slots to provide an airflow gap between the surface

and the vent holes. If not using V Style brackets, be sure to leave a gap between the top of

the unit and the surface for heat to escape.

Twisted Pair Cable Pinouts and RJ-45 LEDs

DXLink (for signal transport) and ICS LAN 10/100 (for Private network connection)

ports both use twisted pair cable. FIG. 3 shows two pinouts that can be used for either

port. FIG. 4 shows the LEDs for each port.

Attaching Signal, Transport, and Control Cables

Important Twisted Pair Cabling Requirements and Recommendations:

• DXLink twisted pair cable runs require shielded category cable (STP) of Cat6A or

Cat7.

• DXLink twisted pair cable runs for DXLink equipment shall only be run within a

common building.*

• DXLink (RJ-45) connectors must not be used for connecting to a standard

Ethernet Network. The connector is used for signal transport.

• Do not create a network (Ethernet) loop. A network loop is created when the

enclosure and one or more of its DXLink Modules are connected to a common

Public LAN.

• DXLink delivers 10.2 Gb/s throughput over shielded category cable. Based on this

bandwidth requirement, we recommend following industry standard practices

designed for 10 Gigabit Ethernet when designing and installing the cable

infrastructure.

• The cables should be no longer than necessary to reach the end-points. We

recommend terminating the cable to the actual distance required rather than

leaving any excess cable in a service loop.

• For complete cable specifications, see the Hardware Reference Manual – DXLink

Twisted Pair 4K Transmitters and Receivers.

* “Common building” is defined as: Where the walls of the structure(s) are physically

connected and the structure(s) share a single ground reference.

For more details and helpful cabling information, reference the white paper titled

“Cabling for Success with DXLink” available at www.amx.com or contact your AMX

representative.

To attach signal and transport cables to the Transmitter:

1. DXLink connector – Attach a twisted pair cable to the DXLink output and to a

DXLink input connector on the RX (requires PoE injector) or on the switcher.

2. Set the Transmitter into single-gang back box.

Fasten to back box with screws.

3. Place decor style cover plate over Transmitter.

Fasten cover plate to Transmitters with screws.

4. HDMI In – Attach an HDMI cable from the source to the HDMI In connector.*

* DVI cable can be used via a cable adapter; however, advanced audio support from

HDMI will not be available.

FIG. 1 DXLINK TWISTED PAIR 4K TX AND RX ENDPOINT SOLUTION (CONNECTED TO DGX800-ENC)

FIG. 2 DXLINK TWISTED PAIR 4K TX AND RX AS EXTENDER SOLUTION

FL T

DXLink

Twisted Pair 4K

Output Board

Twisted pair cable

Enova DGX 800

Destination device

Receiver

Source device

Wallplate

Transmitter

DXLink

Twisted Pair 4K

Input Board

Source device

Destination device

Twisted pair cable

Receiver

Wallplate Transmitter

NOTE: This configuration requires

PS-POE-AT-TC (FG423-84) or

PDXL-2 (FG1090-170) power injector.

PS-POE-AT-TC

HDMI cable

FIG. 3 RJ-45 PINOUTS

FIG. 4 RJ-45 PORTS

FIG. 5 ATTACH SIGNAL AND TRANSPORT CABLES ON DX-TX-DWP-4K

Yellow LED

Green LED

On - Link status is active

Off - Link status is not active

On - Speed status is 100 Mbps

Off - Speed status is 10 Mbps

ICS LAN 10/100 Port

(RX only)

DXLink Port

(TX and RX)

On - Connection established

On - Authenticated HDCP

Flashing - Video active; no HDCP

Off - No Video

DXLink output

HDMI In

registered trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of

their respective companies.

AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.

The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153

AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/

93-1010-330 REV: A

Last Revised: 4/22/2016

To attach signal, transport, and control cables to the Receiver:

1. Set DIP switch toggles if necessary (for settings, see product manual).

2. DXLink input connector – Attach a twisted pair cable from the DXLink output

connector on the switcher (or on a TX) to the DXLink input.

3. HDMI Out – Attach HDMI cable from this port to the destination.

4. Stereo Audio Out jack (optional) – Connect an analog audio cable from this port

to the destination.

5. Apply power (see below).

Applying Power

A desktop power supply (ENERGY STAR® qualified) is provided with each module.

Power can be supplied to DXLink Twisted Pair 4K endpoints by DXLink Power sourcing

devices as follows:

• To a Wallplate TX or an RX module from an Enova DGX Switcher or PS-POE-AT-TC

(FG423-84) or PDXL-2 (FG1090-170).*

• To an RX module from a Solecis 5x1 4K Multi-Format Digital Switcher

(SDX-514M-DX).

* Power Budget: For TXs and/or RXs connected to an Enova DGX, use the Enova DGX

Configuration Tool (www.amx.com/enova) to determine power requirements of a

configuration and if any DXLink RXs should use local power. The tool contains

instructions on how to use it.

Note: Local power takes precedence over DXLink power (via DXLink port) from switcher.

Important: If a desktop power supply is used to power a module, it must be the one

provided, which must not be altered in any way. AMX does not support use of any other

power supplies or PoE injectors as they may potentially damage the DXLink equipment.

To apply power to a Receiver module:

1. Attach the provided clamp-on ferrite bead to the power cord on the AC side of the

provided desktop power supply (as close as possible to the power supply, on the

cord that attaches to an outlet).

2. Plug the cord from the desktop power supply into the power jack on rear of the

Receiver (2.1 mm DC jack for 12 V local power).

3. Plug the desktop power supply into an AC external power source. The Power LED

on the front of the Receiver illuminates green, indicating a ready state.

Table shows DX-RX-4K LED states on power up. If not normal, check connections.

* At power up, the RX defaults to Auto. Press the Scaling button to change the mode.

Table shows DX-TX-DWP-4K LED states on power up. If not normal, check connections.

DXLink Auto-setup with Enova DGX 100 Series Switchers

Auto-setup is the default for using DXLink modules with Enova DGX 100 Series

Switchers. For information about Auto-setup, including how to disable Auto-setup, see

the Hardware Reference Manual – Enova DGX 100 Series Digital Media Switchers. For

information about traditional NetLinx binding (Auto-setup disabled), see the Hardware

Reference Manual – DXLink Twisted Pair 4K Transmitters and Receivers.

USB HID Port (Receiver Rear)

This USB HID port on the Receiver supports passing keyboard and mouse USB signals

to control a remote computer attached via USB to a DXLink Transmitter with compatible

USB HID port (see the Hardware Reference Manual – DXLink Twisted Pair Transmitters/

Receiver).

ID Button (Receiver Front)

The ID button can be used to toggle between static and DHCP IP addressing, assign a

device address, reset the factory defaults, and restore the factory firmware image (for

details, see the Hardware Reference Manual).

Additional Information Covered in Product Manual

For information on the following, see the Hardware Reference Manual – DXLink Twisted

Pair 4K Transmitters and Receivers at www.amx.com :

• Supported input and output resolutions

• Pinouts for HDMI cables and DVI-to-HDMI cable adapters

• NetLinx control and programming commands; Telnet commands

• IR file transfers; upgrading firmware image; restoring factory default settings

• RS-232 Serial data, IR control, and USB HID support information

• Compatibility with DXLink Twisted Pair (non-4K) equipment

Reference Documents

• Hardware Reference Manual – DXLink Twisted Pair 4K Transmitters and Receivers

• Hardware Reference Manual – Enova DGX 100 Series Digital Media Switchers

• Hardware Reference Manual – DXLink Twisted Pair Transmitters/Receiver

• Hardware Reference Manual – Solecis Digital Switchers

• White Paper: Cabling for Success with DXLink

• DXLink – HID Supported Devices

• WebConsole & Programming Guide – NX-Series Controllers

FIG. 6 ATTACH SIGNAL, TRANSPORT, AND CONTROL CABLES ON DXLINK 4K HDMI RECEIVER

INDICATOR LED NORMAL POWER UP INDICATES

Power Green Power is applied

Digital Video and Audio Green Video and HDMI embedded

audio are present

Scaling: Bypass/Auto/Manual One green, two off Current scaling mode*

IR TX / IR RX Red / Yellow IR activity

232 (Serial) TX / 232 (Serial) RX Red / Yellow Serial activity

NetLinx Link/Act Green

(Blinking = #3 Toggle OFF)

Active LAN connection to

an AMX Network

NetLinx Status Green LAN activity

CEC OFF Not currently supported

USB Yellow Connected to device

INDICATOR LED NORMAL

POWER UP

INDICATES

DXLink Green Power applied and DXLink connection established

HDCP

Solid Green Transmitting HDCP-encrypted signal

Blinking Green Transmitting non-encrypted signal

Stereo Audio Out

DXLink input USB HID port HDMI Out

Ground screw ICS LAN 10/100 port

Specyfikacje produktu

Marka:	AMX
Kategoria:	nieskategoryzowany
Model:	FG1010-330-WH
Kolor produktu:	Biały
Rodzaj zasilania:	Prąd przemienny
Częstotliwość wejściowa AC:	50 - 60 Hz
Napięcie wejściowe AC:	100 - 240 V
Wysokość produktu:	106.7 mm
Szerokość produktu:	32.3 mm
Głębokość produktu:	44.5 mm
Waga produktu:	200 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Certyfikaty:	UL 60950-1 2nd Ed. Am2\nCAN/CSA 22.2 No. 60950-1 2nd Ed. Am2\nIEC 60950-1 2nd Ed. Am2\nCE EN 60950-1 2nd Ed. Am2\nCE EN 55022:2010 Class A\nCE EN 55024:2010\nCC CFR Title 47 Part 15 Subpart B Class A\nICES-003 issue 6 Class A\nCISPR 22\nCISPR 24\nWEEE
Liczba kanałów:	5.1 kan.
Waga wraz z opakowaniem:	470 g