Instrukcja obsługi Amprobe ACD-3300-IND

Amprobe Sprzęt pomiarowy ACD-3300-IND

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Amprobe ACD-3300-IND (46 stron) w kategorii Sprzęt pomiarowy. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/46
ACD-3300 IND
ACDC-3400 IND
CAT IV Industrial True
RMS Clamp Meters
Users Manual
Mode d’emploi•
Bedienungshandbuch•
Manuale d’Uso•
Manual de uso•
Användarhandbok•
4
ACD-3300 IND / ACDC-3400 IND
CAT IV Industrial True RMS Clamp Meters
CoNTENTS
Symbols .................................................................................................................................. 5
Safety Information ................................................................................................................ 5
Warnings and Precautions ......................................................................................... 5
Unpacking and Contents ...................................................................................................... 6
Introduction ........................................................................................................................... 6
AUXILIARY FEATURES ........................................................................................................... 6
PEAK+/- Push button ....................................................................................................... 6
MAX/MIN Button ............................................................................................................. 6
ZERO (Relative) Measurements (ACDC-3400 IND only)............................................. 7
HOLD Button .................................................................................................................... 7
RANGE Button .................................................................................................................. 7
Backlight Push Button................................................................................................ 7
Auto Power Off (APO) ..................................................................................................... 7
Operation .............................................................................................................................. 7
Measuring DC Voltage (see Fig. 2) ............................................................................... 7
Measuring AC Voltage (See Fig. 2) ............................................................................... 7
AC Current Measurement (See Fig. 3) .......................................................................... 7
DC Current Measurement (ACDC-3400 IND only) (See Fig. 3) .................................... 7
Frequency Measurement / % Duty Cycle (see ig. 2) ................................................. 8F
Capacitance Measurement (see ig. 4) ......................................................................... 8F
Resistance (See Fig. 5) .................................................................................................. 8
Continuity Testing (See Fig. 5) ...................................................................................... 8
Diode Testing (See Fig. 5) ............................................................................................. 8
Temperature Measurement (ACD 3300 IND only) (See Fig. 6) ................................. 9
Maintenance and Repair ..................................................................................................... 9
Battery Replacement (see Fig. 7) ................................................................................. 9
Specifications ......................................................................................................................... 9
General ............................................................................................................................. 9
Electrical ......................................................................................................................... 10
8
Press the 2. button to null out the DC amps offset.
Open spring-loaded clamp by pressing the lever on left side of meter.3.
Position clamp around one wire or conductor and release the clamp lever. Wire 4.
should be center inside the jaws.
Read the displayed value.5.
Frequency Measurement / % Duty Cycle (see ig. 2) F
Select the “Hz” position. 1.
Connect the test leads: Red to 2. , Black to .+ COM
Connect the test probes to the circuit test points.3.
Read the frequency on the primary display and the Duty cycle on the secondary 4.
display, and, if necessary, correct any overload ( ) conditions.0L
Capacitance Measurement (see ig. 4)F
Note: When the capacitor to be tested is connected and LCD indicates “di .c”, means
there is voltage on the capacitor and needs to be discharged before testing.
Select the “1. ” position.
Connect the test leads: Red to 2. , Black to .+ COM
Connect the test probes to the circuit test points.3.
Read the display and if necessary, correct any overload (4. ) conditions.0L
CAUTION
Using the Resistance or Continuity function in a live circuit will produce false results
and may damage the instrument. In most cases the suspected component must be
disconnected from the circuit to obtain an accurate measurement reading.
Resistance (See Fig. 5)
Set the Function Switch to 1. . Use the ‘ ’ button to select the resistance test Ω Ω
(ACD-3300 IND only).
Connect the test leads: Red to 2. , Black to .+ COM
Turn off power to the circuit being measured. Never measure resistance across a 3.
voltage source or on a powered circuit.
Discharge any capacitors that may influence the reading.4.
Connect the test probes across the resistance.5.
Read the display. If 6. appears on the highest Range, the resistance is too large to be 0L
measured or the circuit is an open circuit.
Continuity Testing (See Fig. 5)
Set the Function Switch to 1. . Use the ‘ ’ button to select the test (ACD-3300 Ω
IND only).
Connect the test leads: Red to 2. , Black to .+ COM
Turn off power to the circuit being measured.3.
Discharge any capacitors that may influence the reading.4.
Connect the test probes across the resistance or the two points of test.5.
Listen for the tone that indicates continuity (< 30 6. ).Ω
Diode Testing (See Fig. 5)
Set the Function knob to the “ 1. “ position. Use the ‘ ’ button to select diode Ω
test (ACD-3300 IND only).
Connect the red test lead to the “V2. ” jack and the black test lead to the “COM” Ω
jack.
Turn off power to the circuit under test. External voltage across the components 3.
causes invalid readings.
Touch probes to the diode. A forward-voltage drop is about 0.6V (typical for a silicon 4.
diode).

Specyfikacje produktu

Marka: Amprobe
Kategoria: Sprzęt pomiarowy
Model: ACD-3300-IND

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Amprobe ACD-3300-IND, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Sprzęt pomiarowy Amprobe

Amprobe

Amprobe RS-3-PRO Instrukcja

26 Września 2024
Amprobe

Amprobe ACDC-100 Instrukcja

18 Września 2024
Amprobe

Amprobe RS-1007-PRO Instrukcja

25 Sierpnia 2024
Amprobe

Amprobe ACDC-3400-IND Instrukcja

15 Sierpnia 2024
Amprobe

Amprobe ACDC-52NAV Instrukcja

8 Sierpnia 2024
Amprobe

Amprobe ACD-3300-IND Instrukcja

4 Lipca 2024

Instrukcje Sprzęt pomiarowy

Najnowsze instrukcje dla Sprzęt pomiarowy

Stamos

Stamos S-LS-28 Instrukcja

15 Października 2024
Stamos

Stamos S-LS-86 Instrukcja

15 Października 2024
Stamos

Stamos S-LS-61 Instrukcja

15 Października 2024
Stamos

Stamos S-LS-81 Instrukcja

15 Października 2024
Stamos

Stamos S-LS-84 Instrukcja

15 Października 2024
Stamos

Stamos S-LS-74 Instrukcja

15 Października 2024
Stamos

Stamos S-LS-76 Instrukcja

15 Października 2024
Stamos

Stamos S-LS-42 Instrukcja

15 Października 2024
Stamos

Stamos S-LS-75 Instrukcja

15 Października 2024
Stamos

Stamos S-LS-35 Instrukcja

15 Października 2024