Instrukcja obsługi American International TOYK989

American International Niesklasyfikowane TOYK989

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla American International TOYK989 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Double DIN Mount Applications

NOTE: Remove shaded pocket support Tabs on left and right bracket.

1. Remove the shaded tab from the bottom of each left and right mounting bracket (See figure C below).

2. Cut and remove center rib from main frame and file edges smooth.

3. Attach the left and right side brackets to the main frame (See figure C below).

4. Follow steps 4-6 from single ISO instructions on page 3.

5. Attach a rear support bracket to the rear of the radio components and adjust as needed

to allow rear support in the sub-dash (optional).

CUSTOMER HELP LINE

8am-4:30 P.S.T. Monday-Friday Except Holidays

USA 800-323-4329 • Canada 800-245-8777

Toyota

2008-12 HIGHLANDER (WITHOUT FACTORY NAVIGATION)

VEHICLE APPLICATIONS

KIT ASSEMBLY INSTRUCTIONS

NOTE: #1 - ISO trim ring (DITR989) must be used in place of after-market radio’s trim rings. For ISO mount

applications, mount after-market radio components to side brackets using screws provided with

radio when possible or hardware included with kit.

For ISO mount only: Attach (1) ISO Spacer to the

inside of lower sections on both Left

& Right mounting brackets as shown in Fig. A.

Cut

Left

Right

Fig. A

DITR989

IMB989L

IMB989R

Fig. C

Main Frame

TOYK989 Mounting Kit

Remove shaded pocket

support Tabs on left

and right bracket.

Single ISO Mount Applications

1. Attach the left and right side brackets to the main bracket. See Figure B.

2. Insert pocket (part # POC989) into upper section of the main frame.

3. Attach left and right side brackets to the rear of the pocket using screws supplied.

4. Attach (1) ISO Spacer to the inside of lower section on both Left & Right mounting

brackets as shown in Fig. A.

5. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides

of radio using screws provided with radio when possible or hardware included with kit.

6. Slide radio component forward or backward for desired look and tighten screws.

7. Attach a rear support bracket to the rear of the new radio and adjust as necessary to

attach to the rear support stud located on the back of the pocket using the small

phillips screw supplied with kit (optional).

KIT ASSEMBLY INSTRUCTIONS

2 3

NOTE: #1 - ISO trim ring (ITR989) may be used in place of after-market radio’s removable trim ring.

ITR989

(BOTTOM

OPTIONAL)

For ISO mount only: Attach (1) ISO

Spacer to the inside of lower section

on both Left & Right mounting

brackets as shown in Fig. A.

Left

POC989

IMB989L

IMB989R

Right

Fig. A

Fig. B

Main Frame

NOTE: ISO trim ring (ITR989) may be used in

place of after-market radio’s removable trim ring.

(Some radio faces may be too large and the

trim ring may need to be modified)

Single DIN Mount Applications

1. Attach the left and right side brackets to the main bracket. See Figure B opposite page.

2. Insert pocket (part # POC-989) into upper section of the main frame.

3. Attach left and right side brackets to the rear of the pocket using screws supplied.

4. Insert DIN sleeve from your new radio into the lower section of the installation kit.

5. Depress the tabs from inside the sleeves opening upward, outward, and downward

to secure sleeve to the installation kit.

6. Install radio into sleeve and lock into place.

7. Attach a rear support bracket to the

rear of the new radio and adjust as

necessary to attach to the rear support

stud located on the back of the pocket

using the small phillips screw supplied

with kit (optional).

1. Carefully unclip and remove the vent panel above the radio. The vent panel is held to

the sub-dash with plastic clips.

2. Lower the glove box door.

3. Remove the climate control panel that extends from the glove box down to the access

door for the auxiliary plug and up to the key cylinder area. The access door is attached

to the trim bezel.

4. Remove the (4) 10mm bolts securing the radio in place.

5. There are (4) plastic clips left holding the radio in the sub dash.

6. Carefully pull forward the radio assembly to remove from the sub-dash.

7. Disconnect all harnesses and antenna leads attached to the radio assembly.

8. Remove the hazard switch assembly from the radio mounting brackets.

This will need to be reinstalled into the new installation kit.

9. Remove the clock assembly from the radio mounting brackets (4) phillips screws).

This will need to be installed in the new kit.

10.Remove the 4 radio support studs from the back of the factory radio.

DASH DISASSEMBLY AND RADIO REMOVAL INSTRUCTIONS

2008-2012 TOYOTA HIGHLANDER

(WITHOUT FACTORY NAVIGATION)

Main Frame

DIN Sleeve

KIT ASSEMBLY INSTRUCTIONS

1. Remove the 4 factory radio (upper + lower side) support studs,

as shown in Fig. D below, and attach to the rear side of the TOYK989

main bezel using the screws from the factory radio.

Fig. D

Support studs

Specyfikacje produktu

Marka:	American International
Kategoria:	Niesklasyfikowane
Model:	TOYK989

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z American International TOYK989, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane American International

American International BMWK300 Instrukcja

5 Października 2024

American International HDK001 Instrukcja

5 Października 2024

American International FM-K574 Instrukcja

4 Października 2024

American International TOYK958 Instrukcja

25 Września 2024

American International NDK754GB Instrukcja

25 Września 2024

American International TOYK975 Instrukcja

25 Września 2024

American International SG600DX Instrukcja

25 Września 2024

American International TOYK980 Instrukcja

25 Września 2024

American International NDK730 Instrukcja

25 Września 2024

American International UPK750 Instrukcja

25 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024