Instrukcja obsługi Amana PWHK01C

Amana piekarnik PWHK01C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Amana PWHK01C (3 stron) w kategorii piekarnik. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
Description
The PTAC Wire Harness kit provides connection from the 14-pin or 18-pin terminal strip on the PTAC control board to the
following board features:
Door Switch*
Motion Sensor*
Emergency Hydronic Heat**
Load Shedding**
Front Desk Control**
Transfer Fan (relay must be manufacturer-approved and have a DC low voltage coil)
Remote Thermostat (must be manufacturer-approved)
The kit includes a 14-pin and an 18-pin female housing with 18 jumper wires and wire nuts. The installation and servicing of
this equipment should be performed by qualified, experienced technicians.
*Contact your sales person for proper manufacturer-approved devices and wiring instructions.
**If other than a “dry switch” is used in connecting these features, consult manufacturer before proceeding.
FD1 (ORANGE)
FD2 (ORANGE)
C (BLACK)
R (RED)
GL (GREEN)
Y (YELLOW)
B (BLUE)
EH (WHITE W/
STRIPES)
IN (RED W/
STRIPES)
LS (YELLOW W/
STRIPES)
GH (GREEN W/
STRIPES)
TF(-) (GRAY W/
STRIPES)
TF(+) (GRAY)
W2 (WHITE)
MS1 (VIOLET)
MS2 (VIOLET)
DS1 (BROWN)
DS2 (BROWN)
PTAC
WIRE HARNESS KIT
(PWHK01C)
INSTALLATION INSTRUCTIONS
Due to policy of continual product
improvement, the right is reserved to
change specifications and design
without notice.
July 2004
Part No.20319103
Printed in U.S.A.
2
WARNING
DISCONNECT ELECTRICAL POWER SOURCE BEFORE WIRING THE UNIT.
FAILURE TO DO SO MAY RESULT IN INJURY OR DEATH FROM ELECTRICAL
SHOCK. THE UNIT "OFF" SWITCH DOES NOT DISCONNECT ALL POWER TO
THE UNIT.
INSTALLATION
WARNING
ALL WIRING MUST COMPLY WITH APPLICABLE LOCAL AND NATIONAL CODES.
TYPE AND LOCATION OF FUSED DISCONNECT SWITCH(ES) MUST COMPLY
WITH ALL APPLICABLE CODES.
1. Disconnect power and remove the front panel per unit
installation instructions.
2. Remove 14-pin (or 18-pin, if applicable) female housing
from control board.**
Using the following table and either Figure 1 or 2 as
guides, (Figure 1 for boards with knobs; Figure 2 for
boards with touchpads) choose the feature desired and
insert the proper jumper wire into the appropriate slot on
the housing. Ensure the jumper wires are oriented as
shown in Figure 3.
Re-install the 14-pin or 18-pin housing. Ensure housing
faces the direction shown in either Figure 1 or 2. Take
EH
IN
LS
FD1
FD2
TF(-)
TF(+)
C
R
GL
W2
Y/W1
B
GH
Figure 1: Control Knobs (14-pin Units)
Fea ture Pins Used
Emergency Hydronic Heat EH, IN
Load Shedding LS, IN
Front Desk Control FD1, FD2
Transfer Fan TF(-), TF (+)
Remote Thermostat C, R, GL, W 2, Y/W 1, B, GH
Motion Sensor* MS1, MS2
Door Switch* DS1, DS2
Table 1
*These features and connections are only available on touchpad control 18-pin units.
**If a female housing is not present on the control board, use the housing supplied with this kit.
DS1 DS2 MS1 MS2 EH IN LS FD1 FD2 TF- TF+ C R GL W2 Y/W1 B GH
Figure 2: Touchpad (18- Pin Units)
care to ensure the plastic housing and metal pins are
aligned correctly; otherwise, the unit will not funciton
properly.
NOTE: Only load wires intended for installation. Extra
wires can be used to connect other PTAC boards. One
PWHK01C kit can be used for multiple boards.
3. Connect the kit wiring to the field wiring using the wire
nuts provided. Route the kit wiring as shown in Figure 4.
Do not run wires through basepan or wall sleeve.
4. With the unit in the OFF position, reconnect the power
and ensure the master switch is in the ON position.
5. Reinstall the front cover per unit installation instructions.
Check the unit for proper operation.
Figure 3
14-PIN 18-PIN
3
Figure 4
Route low voltage wire as
shown above. No holes
are permitted in chassis
basepan or wallsleeve
when routing low voltage
wire.
123
ON
Route low voltage wire as
shown above. No holes
are permitted in chassis
basepan or wallsleeve
when routing low voltage
wire.

Specyfikacje produktu

Marka: Amana
Kategoria: piekarnik
Model: PWHK01C

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Amana PWHK01C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje piekarnik Amana

Amana

Amana AES3540BAW Instrukcja

12 Stycznia 2025
Amana

Amana AER5511AAB14 Instrukcja

12 Stycznia 2025
Amana

Amana AER4111AAW Instrukcja

12 Stycznia 2025
Amana

Amana AGR4203MNB Instrukcja

5 Października 2024
Amana

Amana AER5735QAS Instrukcja

22 Września 2024
Amana

Amana AOES3030E Instrukcja

18 Września 2024
Amana

Amana ACR4503SFB Instrukcja

17 Września 2024
Amana

Amana AWO6317SFS Instrukcja

16 Września 2024
Amana

Amana ACR2303MFW Instrukcja

16 Września 2024
Amana

Amana AER4111AAW10 Instrukcja

15 Września 2024

Instrukcje piekarnik

Najnowsze instrukcje dla piekarnik

Ariston

Ariston F48 1012 C.1 Instrukcja

27 Marca 2025
Ariston

Ariston FM 52 F Instrukcja

27 Marca 2025
Smeg

Smeg cs 71 5 Instrukcja

27 Marca 2025
Viking

Viking RVDOE330 Instrukcja

27 Marca 2025
Monogram

Monogram ZDP486NDTSS Instrukcja

26 Marca 2025
Whirlpool

Whirlpool WOI4S8HM1SXA Instrukcja

25 Marca 2025
AEG

AEG NBU5A20SB Instrukcja

24 Marca 2025
AEG

AEG NBU5P40BCK Instrukcja

24 Marca 2025
AEG

AEG TA5PB53WAB Instrukcja

24 Marca 2025
AEG

AEG OU5AE20AK Instrukcja

24 Marca 2025