Instrukcja obsługi Amana NGD5700BW

Amana Suszarka bębnowa NGD5700BW

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Amana NGD5700BW (44 stron) w kategorii Suszarka bębnowa. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/44
W10573707B
W10573708B-SP
GAS DRYER INSTALLATION INSTRUCTIONS
CANADIAN ELECTRIC DRYER INSTRUCTIONS
INSTRUCTIONS POUR L’INSTALLATION DE LA SÉCHEUSE
À GAZ (É.-U. ET CANADA)
ÉLECTRIQUE (CANADA UNIQUEMENT)
Table of Contents
DRYER SAFETY 2 ..........................................................................
INSTALLATION REQUIREMENTS 4 ..............................................
Tools and Parts 4 ......................................................................
LOCATION REQUIREMENTS 5 .....................................................
ELECTRIC DRYER POWER HOOKUP-CANADA ONLY 6 ...........
GAS DRYER POWER HOOKUP 7 .................................................
INSTALL LEVELING LEGS 9 ..........................................................
MAKE GAS CONNECTION 9 .........................................................
VENTING 10 ....................................................................................
Venting Requirements 10 .........................................................
Plan Vent System 11 .................................................................
Install Vent System 12 ..............................................................
CONNECT INLET HOSE (STEAM MODEL ONLY)................... 12
CONNECT VENT 14 .......................................................................
LEVEL DRYER 14 ...........................................................................
COMPLETE INSTALLATION CHECKLIST 15 ...............................
DOOR REVERSAL (OPTIONAL) 15 ...............................................
INSTALLATION NOTES
Date of purchase: _________________________________
Date of installation: _______________________________
Installer: ________________________________________
Model number: ___________________________________
Serial number: ___________________________________
Date d’achat: ______________________________________
Date d’installation: __________________________________
Installateur: _______________________________________
Numéro de modéle: _________________________________
Numéro de série: ___________________________________
NOTES CONCERNANT L’INSTALLATION
Para una version de estas instrucciones en español, visite www.Whirlpool.com
Table des matières
SÉCURITÉ DE LA SÉCHEUSE 23 ..................................................
EXIGENCES D’INSTALLATION 25 .................................................
Outillage et pièces 25 .............................................................
EXIGENCES D’EMPLACEMENT 26 ...............................................
SÉCHEUSE ÉLECTRIQUE RACCORDEMENT À
L’ALIMENTATION ÉLECTRIQUE - CANADA SEULEMENT 27 .....
RACCORDEMENT D’UNE SÉCHEUSE À GAZ 28 ........................
INSTALLATION DES PIEDS DE NIVELLEMENT 30 ......................
RACCORDEMENT AU GAZ 30 .......................................................
ÉVACUATION 31 .............................................................................
Exigences concernant l’évacuation 31 .................................
Planication du système d’évacuation 32 ............................
Installation du système d’évacuation 34 ...............................
RACCORDEMENT DU TUYAU D’ALIMENTATION
(MODÈLE À VAPEUR UNIQUEMENT) 34 ......................................
RACCORDEMENT DU CONDUIT D’ÉVACUATION 36 .................
RÉGLAGE DE L’APLOMB DE LA SÉCHEUSE..........................36
ACHEVER L’INSTALLATION LISTE DE VÉRIFICATION 37 ...........
INVERSION DE LA PORTE (FACULTATIF) 37 ................................
2
DRYER SAFETY
3
IMPORTANT: When discarding or storing your old clothes dryer, remove the door.
4
INSTALLATION REQUIREMENTS
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
Tools needed for all installations:
Level
Tape measure Pliers
Flat-blade screwdriver #2 Phillips screwdriver
Adjustable wrench that opens to
1" (25 mm) or hex-head socket wrench
Tin snips (new vent installations)
Caulking gun and compound
(new vent installations)
1/4" and 5/16" nut driver
(recommended)
Leveling legs (4)
Tools needed for gas installations:
8" or 10" pipe wrench 8" or 10" adjustable wrench
(for gas connections)
Pipe-joint compound
resistant to LP gas
Utility knife
“Y” connector
Parts package is located in dryer drum. Check that all parts
are included.
NOTE: Do not use leveling legs supplied with dryer if installing
with a pedestal or a stack kit.
Additional parts may be required, depending in your installation.
Check local codes. Check existing electrical supply and venting.
Read “Electrical Requirements” and “Venting Requirements”
before purchasing parts.
Optional Equipment: (Not supplied with dryer)
Refer to your Use and Care Guide for information about
accessories available for your dryer.
Parts supplied (all models):
Parts supplied (steam models):
2' (0.6 m) inlet hose 5' (1.52 m) inlet hose
and rubber washer
Parts needed (steam models):
Parts needed: (Not supplied with dryer)
Vent clamps
Vent elbows and vent work
5
LOCATION REQUIREMENTS
You will need:
A location allowing for proper exhaust installation.
See “Venting Requirements.”
A separate 15 or 20 amp circuit for a gas dryer or 30 amp
circuit for an electric dryer.
If using power supply cord, a grounded electrical outlet
located within 2 ft. (610 mm) of either side of dryer.
See “Electrical Requirements.”
Floor must support dryer weight of 200 lbs. (90.7 kg).
Also consider weight of companion appliance.
Cold water faucets located within 4 ft. (1.2 m) of the water
ll valves, and water pressure of 20 – 120 psi (138 – 827 kPa).
You may use the water supply for your washer using the
supplied “Y” connector and a short hose (which you will
need to purchase).
Level oor with maximum slope of 1" (25 mm) under entire
dryer. If slope is greater than 1" (25 mm), install Extended
Dryer Feet Kit, Part Number 279810. If not level, clothes
may not tumble properly and automatic sensor cycles may
not operate correctly.
For garage installation, place dryer at least 18" (460 mm)
above oor. If using a pedestal, you will need 18" (460 mm)
to bottom of dryer.
The dryer must not be installed or stored in an area where
it will be exposed to water and/or weather.
IMPORTANT: Do not operate, install, or store dryer where
it will be exposed to water, weather, or at temperatures below
40° F (4° C). Lower temperatures may cause dryer not to
shut off at end of automatic sensor cycles, resulting in longer
drying times.
27"
(686 mm)
383/4" Min.
(984 mm)
39" Max.
(990 mm)
Back view:
61/4"
(159 mm)
297/8"*
(759 mm)
31/2"*
(89 mm)
53/4"*
(146 mm)
61/8"*
(156 mm)
143/8"
(365 mm)
253/4"
(654 mm)
3
/4"*
(18 mm)
NOTE: Most installations require a minimum of 5" (127 mm)
clearance behind dryer for exhaust vent with elbow. See “Venting
Requirements.”
Side view:
Front view:
* Approx. measurement
DRYER DIMENSIONS
Gas
* Approx. measurement
Water inlet
(Steam Models Only)
Vent
6
Installation spacing for recessed area
or closet installation
All dimensions show recommended and minimum spacing
allowed.
Additional spacing should be considered for ease of
installation and servicing.
Additional clearances might be required for wall, door, oor
moldings, dryer venting, and gas line.
Additional spacing should be considered on all sides
of the dryer to reduce noise transfer.
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also be considered.
18" min.
(457 mm)
1"
(25 mm)
5"
(127 mm)
24 in.2 min.
(155 cm2)
48 in.2 min.
(310 cm2)
3"
(76 mm)
3"
(76 mm)
1"
(25 mm)
Recommended installation clearances (dryer only):
Mobile home installations require:
Metal exhaust system hardware, available for purchase from
your dealer. For further information, see “Assistance or
Service” section in your Use and Care Guide.
Special provisions must be made in mobile homes to
introduce outside air into dryer. Openings (such as a nearby
window) should be at least twice as large as dryer exhaust
opening.
For mobile home installation of gas dryers:
Mobile Home Installation Hold-down Kit Part Number 346764
is available to order. For further information, see “Assistance
or Service” section in your Use and Care Guide.
ELECTRIC DRYER
POWER HOOKUP – CANADA ONLY
ELECTRICAL REQUIREMENTS
It is your responsibility:
To contact a qualied electrical installer.
To be sure that the electrical connection is adequate and in
conformance with Canadian Electrical Code, C22.1 – latest
edition and all local codes. A copy of above codes standard
may be obtained from: Canadian Standards Association,
178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.
To supply the required 4 wire, single phase, 120/240 volt,
60 Hz, AC only electrical supply on a separate 30-amp circuit,
fused on both sides of the line. A time-delay fuse or circuit
breaker is recommended. Connect to an individual branch
circuit.
This dryer is equipped with a CSA
International Certied Power Cord
intended to be plugged into a standard
14-30R wall receptacle. The cord is 5 ft.
(1.52 m) long. Be sure wall receptacle is
within reach of dryer’s nal location. 4-wire receptacle
(14-30R)
*
* 0" (0 mm) spacing is allowed.
Installation Clearances
For each arrangement, consider allowing more space for ease
of installation and servicing; spacing for companion appliances
and clearances for walls, doors, and oor moldings. Space
must be large enough to allow door to fully open. Add spacing
on all sides of dryer to reduce noise transfer. If a closet door
or louvered door is installed, top and bottom air openings
in door are required.
Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning appliance can be installed in the
same closet as a dryer.
Mobile home – Additional installation requirements:
This dryer is suitable for mobile home installations.
The installation must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR,
Part 3280 (formerly the Federal Standard for Mobile home
construction and Safety, Title 24, HUD Part 280) or Standard
CAN/CSA-Z240 MH.
*
8
*53/4"
(146 mm)
11/2"
(38 mm)
†®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.
3/8" NPT dryer gas pipe
GAS SUPPLY LINE
Option 1 (Recommended Method)
Flexible stainless steel gas connector:
If local codes permit, use a new exible stainless steel gas
connector (Design Certied by the American Gas Association
or CSA International) to connect your dryer to the rigid gas
supply line. Use an elbow and a 3/8" are x 3/8" NPT adapter
tting between the stainless steel gas connector and the dryer
gas pipe, as needed to prevent kinking.
Option 2 (Alternate Method)
Approved aluminum or copper tubing:
Must include 1/8" NPT minimum plugged tapping accessible
for test gauge connection, immediately upstream of the gas
connection to the dryer. See illustration.
1/2" IPS pipe is recommended.
3/8" approved aluminum or copper tubing is acceptable for
lengths under 20 ft. (6.1 m) if local codes and gas supplier
permit.
If you are using Natural gas, do not use copper tubing.
Lengths over 20 ft. (6.1 m) should use larger tubing and
a different size adapter tting.
If your dryer has been converted to use LP gas, 3/8" LP
compatible copper tubing can be used. If the total length of the
supply line is more than 20 ft. (6.1 m), use larger pipe.
NOTE: Pipe-joint compounds that resist the action of LP gas
must be used. Do not use TEFLON®† tape.
Must include shut-off valve
In the U.S.A.:
An individual manual shut-off valve must be installed within
six (6) ft. (1.8 m) of the dryer in accordance with the National
Fuel Gas Code, ANSI Z223.1. The location should be easy to
reach for opening and closing.
In Canada:
An individual manual shut-off valve must be installed in
accordance with the B149.1, Natural Gas and Propane
Installation Code. It is recommended that an individual
manual shut-off valve be installed within six (6) ft. (1.8 m) of
the dryer. The location should be easy to reach for opening
and closing.
GAS SUPPLY CONNECTION REQUIREMENTS
Use an elbow and a 3/8" are x 3/8" NPT adapter tting
between the exible gas connector and the dryer gas pipe,
as needed to avoid kinking.
Use only pipe-joint compound. Do not use TEFLON® tape.
This dryer must be connected to the gas supply line with a
listed exible gas connector that complies with the standard for
connectors for gas appliances, ANSI Z21.24 or CSA 6.10.
BURNER INPUT REQUIREMENTS
Elevations above 2,000 ft. (610 m):
When installed above 2,000 ft. (610 m) a 4% reduction of the
burner Btu rating shown on the model/serial number plate is
required for each 1,000 ft. (305 m) increase in elevation.
Gas supply pressure testing
The dryer must be disconnected from the gas supply piping
system during pressure testing at pressures greater than
1/2 psi.
DRYER GAS PIPE
The gas pipe that comes out through the rear of your dryer has
a 3/8" male pipe thread.
A. 3/8" exible gas connector
B. 3/8" pipe to are adapter tting
C. 1/8" NPT minimum plugged tapping
D. 1/2" NPT gas supply line
E. Gas shut-off valve.
A
B
E
D
C
* NOTE: If the dryer is mounted on a pedestal, the gas
pipe height must be an additional 10" (254 mm) or
15.5" (394 mm) from the oor, depending on the pedestal
model. For a garage installation, the gas pipe height must
be an additional 18" (460 mm) from the oor.

Specyfikacje produktu

Marka: Amana
Kategoria: Suszarka bębnowa
Model: NGD5700BW

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Amana NGD5700BW, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Suszarka bębnowa Amana

Amana

Amana NDE5800AYW Instrukcja

21 Września 2024
Amana

Amana NED5100TQ Instrukcja

17 Września 2024
Amana

Amana NDE2330AYW Instrukcja

15 Września 2024
Amana

Amana NED5800HW Instrukcja

13 Września 2024
Amana

Amana NDE7800AYW Instrukcja

13 Września 2024
Amana

Amana YNED4600YQ Instrukcja

12 Września 2024
Amana

Amana NEC3240FW Instrukcja

12 Września 2024
Amana

Amana YNED5800TQ0 Instrukcja

12 Września 2024
Amana

Amana NDG5800AWW Instrukcja

11 Września 2024
Amana

Amana NGD5700BW Instrukcja

11 Września 2024

Instrukcje Suszarka bębnowa

Najnowsze instrukcje dla Suszarka bębnowa

Whirlpool

Whirlpool C WD 104M WBS SPT Instrukcja

25 Marca 2025
Whirlpool

Whirlpool C WSD 74M WBS ES Instrukcja

25 Marca 2025
Whirlpool

Whirlpool WP C9 WBS EE Instrukcja

25 Marca 2025
Whirlpool

Whirlpool WP C10X WBS EE Instrukcja

25 Marca 2025
Whirlpool

Whirlpool WP C8 WBS EE Instrukcja

25 Marca 2025
Whirlpool

Whirlpool AZB 6570 Instrukcja

24 Marca 2025
Whirlpool

Whirlpool awz 9999 Instrukcja

24 Marca 2025
Pitsos

Pitsos WTP704D8 Instrukcja

22 Marca 2025
Bosch

Bosch WQG2420WFG Instrukcja

21 Marca 2025
Profilo

Profilo KM8612HTR Instrukcja

21 Marca 2025