Instrukcja obsługi Alto TS 112 W

Alto głośnik TS 112 W

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Alto TS 112 W (20 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/20
QUICKSTART GUIDE
ENGLISH
GUÍA DE INICIO RÁPIDO
ESPAÑOL
GUIDE D'UTILISATION RAPIDE
FRANÇAIS
GUIDA RAPIDA
ITALIANO
SCHNELLSTART-ANLEITUNG
DEUTSCH
SNELSTARTGIDS
NEDERLANDS
2
www.a ltoprofess ional.com/wireles swww.a ltoprofess ional.com/wireles s
BOX CONTENTS
• Truesonic Wireless speaker
• Power cable
• Quickstart Guide
• Safety Instructions & Warranty Information Booklet
INSTALLATION
This speaker should be installed on a stand on the
floor, according to its maximum weight, or suspended
from its suspension points (M10 x 1.5PH, 30mm
length) (see example image). We do NOT recommend
suspending multiple speakers in a vertical array.
CONNECTION DIAGRAM
*Note: Microphones, mixer, and cables are not included. Second Truesonic Wireless
speaker sold separately.
Mixer*
Power
Power
Microphones*
Speaker Speaker*
This diagram is a suggestion for setting up the speaker with audio connections. To pair
the speaker with a Bluetooth™ device, see the BLUETOOTH PAIRING & LINKING
section below.
Eyebolt
Dust cover
Suspension
point
Example:
3
BLUETOOTH PAIRING & LINKING
IMPORTANT:
• These steps are for wireless audio streaming only.
• When pairing or linking, do only one process at a time. Starting one process before the other is finished
will cancel the first.
• The tone sequences for pairing and linking are different, so you can easily distinguish between the two.
ABOUT RANGE
Truesonic wireless loudspeakers use an advanced, extended-range Bluetooth antenna design, allowing for
ranges far greater than traditional Bluetooth devices. The typical range is 60-80 feet (18-24 meters) with a
clear line of sight. However, the range may vary depending on your source device and the environment.
To maximize the range:
• Set your source device on a flat surface and make sure there are no obstacles between the
loudspeaker and your device (e.g., walls, furniture, etc.).
• Turn off your source device’s Wi-Fi.
• Turn off any unneeded 2.4 GHz devices in the nearby vicinity (e.g., other Bluetooth devices, baby
monitors, Wi-Fi access points, microwave ovens, etc.).
• Try using a different Bluetooth source device. Bluetooth signal strength varies between different
devices.
PAIRING
To pair the speaker to your Bluetooth device:
1. Do this on one loudspeaker only: With the loudspeaker powered on, press and release its PAIR
BUTTON. Its LED will flash, and you will hear a tone sequence from the loudspeaker. (If you are using
two Truesonic wireless loudspeakers, this one will be the "master." Also see the LINKING section
below.)
2. From your Bluetooth device’s settings page, enable
Bluetooth and select ALTO PRO WIRELESS
TS112W as the device. When paired successfully,
you will hear a final "confirmation tone" from the
loudspeaker and the PAIR BUTTON LED will light
continuously. (This process may take up to 60
seconds.)
Note: If your device prompts you to select the con reo speakers,” “advanced nection type, select “ste
audio,” or a similar option.
3. Turn the loudspeaker's BLUETOOTH VOLUME knob to its lowest setting.
4. On your Bluetooth device, play music. We recommend setting the playback volume at its maximum
setting. Then, adjust the loudpeaker’s BLUETOOTH VOLUME knob to the desired level.
5. Once your device is paired to the speaker, the speaker will remember the device even after power-
cycling it. To reconnect it, go to your device’s Bluetooth settings page and select “Connect” to re-
establish the connection
LINKING
If you are using two Truesonic wireless speakers:
1. Make sure no audio is playing from your Bluetooth
device. If it is, pause/stop playback and wait 5
seconds.
2. Press and release the STEREO LINK BUTTON on
each speaker.
3. Both loudspeakers’ LEDs will flash while
"searching" for each other, and you will hear a tone
sequence from both loudspeakers. (This process may take up to 60 seconds. However, the very first
time you link the loudspeakers, the process may take up to 3 minutes.)
4. When they are successfully linked, you will hear a final "confirmation tone" from both loudspeakers and
the STEREO LINK BUTTON LEDs on both loudspeakers will light continuously.
Note: The stereo signal will be split between the two loudspeakers: the master loudspeaker will play the left
channel; the slave loudspeaker will play the right channel.
Tip: When using two loudspeakers, we recommend labeling the master loudspeaker so you can distinguish
between the two in future setups.
Bluetooth is a registered trademark of Bluetooth SIG.
Note: If your device prompts you to enter
a PIN code to pair it to the speaker, enter
0000 (four zeros).
Note: The loudspeaker that is connected
to your source device is the “master”; the
linked loudspeaker is the “slave.” The
source device sends its signal to the
master, and the master relays the signal to
the slave.

Specyfikacje produktu

Marka: Alto
Kategoria: głośnik
Model: TS 112 W

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Alto TS 112 W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Alto

Alto

Alto Tourmax SX 115 Instrukcja

3 Października 2024
Alto

Alto Busker Instrukcja

29 Września 2024
Alto

Alto Uber LT Instrukcja

22 Września 2024
Alto

Alto TX212 Instrukcja

12 Września 2024
Alto

Alto TX208 Instrukcja

9 Września 2024
Alto

Alto TS 112 W Instrukcja

5 Września 2024
Alto

Alto TS312 Instrukcja

3 Września 2024
Alto

Alto TS415 Instrukcja

2 Września 2024
Alto

Alto TS310 Instrukcja

1 Września 2024
Alto

Alto Black15 Instrukcja

1 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Yamaha

Yamaha DZR10-D Instrukcja

11 Grudnia 2024
Yamaha

Yamaha DZR15-D Instrukcja

11 Grudnia 2024
Yamaha

Yamaha DXS15XLF-D Instrukcja

11 Grudnia 2024
Yamaha

Yamaha NS-2000A Instrukcja

11 Grudnia 2024
Bogen

Bogen WMT1AS Instrukcja

11 Grudnia 2024
Ruark Audio

Ruark Audio Sabre-R Instrukcja

11 Grudnia 2024
Antelope

Antelope R4S Instrukcja

11 Grudnia 2024
Antelope

Antelope Atlas i8 Instrukcja

11 Grudnia 2024
MB

MB PESSPROVS62A Instrukcja

11 Grudnia 2024
MB

MB PESSPROVS32A Instrukcja

11 Grudnia 2024