Instrukcja obsługi Alpine S-W8D2

Alpine subwoofer S-W8D2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Alpine S-W8D2 (8 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
R/S-DB8V-TRK Truck Enclosure Installation Manual
Compatible with the following models:
R2-W8D2
S-W8D2
Introduction
Congratulations on purchasing this truck enclosure. This installation manual is designed to take you through the step-
by-step installation of the ‘R’ or ‘S’ Series Dual 8” Subwoofer Vented Enclosure for Trucks. Please familiarize yourself
with the owners manual and if you still have additional questions please contact our support team at 1-800-TECH-
101.
Note: To ensure safe use, Always follow these precautions.
The installation of this product requires specialized skills and experience. We recommend that you have the product
installed by an Alpine authorized dealer.
Before you use this product, be sure to carefully read this installation manual so that you can use the product
correctly, Failing to do so could lead to damaged equipment or an accident. Alpine Electronics bears no responsibility
for problems that arise as a result of failure to follow the instructions in the manual.
Make sure enclosure is secured to the vehicle. Failing to do so can lead to electric shock, injury or damage to
equipment.
When making a hole in the vehicle body, be careful to avoid damaging pipes, the fuel tank, electrical wiring,
and the like. This kind of damage could lead to an accident or fire.
Do not install the product where it may be exposed to water or in a place with high levels of humidity or dust.
Doing so could lead to fire or damaged equipment.
Start all screw threads by hand and avoid overtourqing screws, failure to do so may damage your equipment.
Matching Alpine mono ampliers are sold separately - check with an Alpine authorized dealer.
Recommended Amplifier settings
R-A75M amp S-A60M amp
Gain=1 o’clock position
LP Filter=70Hz
Bass EQ=0 (Off)
Subsonic Filter=30Hz
Gain=1 o’clock position
LP Filter=70Hz
Bass EQ=0 (Off)
(Note: If available with your HU/DSP -
We recommend a Subsonic lter, if possible
with Fc=30Hz @-24dB/Oct.)
Tools Required
Hex Key Driver (2pcs. included) Power Drill with a Low Torque Setting (Optional)
4mm 3mm
Note:
Use Hex Key Drivers for Enclosure feet, Front/Rear brackets and
amp tray: Failure do so could result in damage to the enclosure.
Note:
Power Drill for Subwoofer and Amplifier installation only.
Accessory List
Driver Side Enclosure Passenger Side Enclosure
Front/Rear Link Bracket Front Cover/Trim Bars
Front Rear
Left/Right Amp Tray Bracket Stacking Feet for Enclosure
6 Standard Stacking Feet
(Rubber/Washer/Rubber)
2 Pair Extra Parts
(Rubber/Washer)
1 Installation screws are temporarily installed in both
driver and passenger side enclosures. Remove all
screws to prepare for assembly.
Stacking feet screws
Front bracket screws
Rear bracket screws
Amp bracket screws
Stacking feet screws
Front bracket screws
Driver side Passenger side
2 If applicable, attach inner amp tray brackets using
supplied M5x20mm screws (4pcs.) and M5x20mm
washers (4pcs.).
Note: Amp tray brackets can be trimmed for narrow
applications. Amp tray will not be used in some
applications - See fitment chart. If Amp brackets are
not installed, the 4 mount screws should be left snugly
tightened in both enclosures.
Caution: To avoid damage to the enclosure use supplied
Hex Key driver for when installing the amp brackets.
Amp tray brackets
3 Place enclosures upside down on a flat surface
and set to required width. Align rear link bracket
with threaded inserts and secure bracket using
supplied M5x20mm screws (4pcs.) and M5x12mm
washers (4pcs.).
Caution: To avoid damage to the enclosure use supplied
Hex Key driver for when installing the rear bracket.
Rear bracket
See Table 1
4 Rotate assembly rightside up and attach front link
bracket using supplied M5x20mm screws (4pcs.)
and M5x20mm washers (4pcs.) as shown.
Caution: To avoid damage to the enclosure use supplied
Hex Key driver for when installing the front bracket.
Front bracket
5 Using the supplied M5x60mm screws (6pcs.)
and M5x20mm washers (6pcs.) install feet as
shown. Additional feet spacers are included to
accomodate vehicles with uneven floors, floor
mats etc. - see fitment chart.
Caution: To avoid damage to the enclosure use supplied
Hex Key driver for when installing the enclosure feet.
6 Place mono amplifier on amp tray and mark
the mount holes. Then drill and mount with
appropriate size screws (not included).

Specyfikacje produktu

Marka: Alpine
Kategoria: subwoofer
Model: S-W8D2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Alpine S-W8D2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje subwoofer Alpine

Alpine

Alpine SS-SB12 Instrukcja

25 Września 2024
Alpine

Alpine KTE-12G.2 Instrukcja

22 Września 2024
Alpine

Alpine S-W10D2 Instrukcja

18 Września 2024
Alpine

Alpine R-W12D2 Instrukcja

15 Września 2024
Alpine

Alpine R-W10D2 Instrukcja

8 Września 2024
Alpine

Alpine RS-W12D4 Instrukcja

7 Września 2024
Alpine

Alpine RS-W10D4 Instrukcja

3 Września 2024
Alpine

Alpine S-W8D4 Instrukcja

2 Września 2024
Alpine

Alpine RS-W10D2 Instrukcja

2 Września 2024
Alpine

Alpine R2-W8D2 Instrukcja

2 Września 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

Pioneer

Pioneer TS-W257D2 Instrukcja

13 Stycznia 2025
Vonyx

Vonyx SWP15 Instrukcja

13 Stycznia 2025
Kicker

Kicker 51MWF104 Instrukcja

13 Stycznia 2025
Kicker

Kicker 51MWF124 Instrukcja

13 Stycznia 2025
Kicker

Kicker 48CWR154 Instrukcja

12 Stycznia 2025
Deaf Bonce

Deaf Bonce Machete MFX30D2 Instrukcja

11 Stycznia 2025
Kicker

Kicker 51MWE104 Instrukcja

10 Stycznia 2025
Kicker

Kicker 51MWE124 Instrukcja

10 Stycznia 2025
Phoenix Gold

Phoenix Gold ZP12D4 Instrukcja

9 Stycznia 2025
Phoenix Gold

Phoenix Gold ZP12D2 Instrukcja

9 Stycznia 2025