Instrukcja obsługi Air King 99539

Air King Wentylator 99539

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Air King 99539 (8 stron) w kategorii Wentylator. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

Designed for cooling workers in factories, warehouses, manufacturing facilities and garages where

humid and demanding conditions exist. All circulator heads have high efciency corrosion resistant

propellers with steel blades. Circulator heads utilize a vertical tilt/locking adjustment for directional

ow. Wire guards are black power-coated steel and comply with OSHA Standard 1910.212 (1/2”

maximum opening). All circulator heads are oscillating that sweep through a 45 or 90 arc.° °

Operating Instructions & Parts Manual Models: 99538, 99539

24” & 30” Quiet Design

Oscillating Wall Mount Fan

Unpacking

1. Inspect for any damage that may have occurred during transit.

2. Shipping damage claim must be led with carrier.

3. Check all bolts, screws, setscrews, etc. for looseness that

may have occurred during transit. Retighten as needed.

Oscillating Dimensions and Specications

99539 24” 20 1/4” 26 3/4” 120 60 3 3 Wall Mount

99538 30” 20 1/4” 33 3/8” 120 60 3 3 Wall Mount

Prop.

Model Dia. A B Volts Hz Speeds Blades Mounting Accessory

99539 24” 1025/880/480 1/4 5030 4320 2280 500/350/220 7.7/5.7/1.8 2.3/1.6/0.6 3.5

99538 30” 1010/860/530 1/4 7450 6090 3450 700/520/300 6.7/5.4/2.0 2.3/1.6/0.6 3.7

Prop. Motor CFM Air Velocity Sones @ Operating Full Load

Model Dia. RPM HP High Med Low @ 20 Ft. (FPM) 0.000SP Amps Amps

PLEASE READ AND SAVE THESE INSTRUCTIONS. Read carefully before attempting to assemble, install, operate or

maintain the product described. Protect yourself and others by observing all safety information. Failure to comply

with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

Printed in U.S.A. New 5/11 5085459

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should always be followed to reduce the

risk of re, electric shock and injury to person, including the following:

24” & 30” Quiet Design

Oscillating Wall Mount Fan

1. Read all instructions before using Fan.

2. Make certain that the power source con-

forms to the electrical requirements of the

Fan.

3. Use this Fan only as described in this manual.

Any other use not recommended by the

manufacturer may cause re, electrical shock,

or injury to persons.

4. To reduce the risk of personal injury and elec-

tric shock, the Fan should not be played with

or placed where small children can reach it.

5. Unplug power cord before servicing, or

moving the Fan.

WARNING: DO NOT DEPEND UPON THE

ON-OFF SWITCH AS THE SOLE MEANS OF

DISCONNECTING POWER WHEN INSTALLING

OR SERVICING THE FAN. ALWAYS UNPLUG

THE POWER CORD.

6. This Fan must NOT be used in potentially

dangerous locations such as ammable,

explosive, chemical-laden or wet atmo-

spheres.

7. DO NOT use Fan in or near a window. Rain

may create an electrical hazard.

8. Completely reassemble Fan, according to

instructions, before reconnecting to power

supply.

9. The power cord is equipped with a three-

prong grounded plug that be inserted should

into a matching receptacle. Under no

circumstances should the grounding prong

be cut off the plug. Where a two-prong

wall receptacle is encountered, it must be

replaced with a properly grounded three-

prong receptacle installed in accordance

with the National Electrical Code (NEC) and

all applicable local codes and ordinances.

This work must be done only by a qualied

electrician, using copper wire only.

GENERAL SAFETY INFORMATION

When using electrical appli-

ances, basic precautions should

always be followed to reduce

the risk of re, electric shock and

injury to person, including the

following:

WARNING: USE OF A THREE-PRONG

TO TWO-PRONG ADAPTER IS NOT REC-

OMMENDED. IMPROPER CONNECTION

MAY CREATE THE RISK OF ELECTRICAL

SHOCK IS . USE OF SUCH ADAPTERS

NOT PERMITTED IN CANADA.

10. Where possible, avoid the use of

extension cords. If they must be used,

minimize the risk of overheating by

ensuring that they are UL listed. Never

use a single extension cord to operate

more than one Fan. Do not plug Fan

into any other cord connected device,

such as a power strip, cord reel, surge

protector, multiple outlet adapters or

outlet-type air fresheners. The use of

such devices may create a re hazard.

11. Do not operate any Fan with a

damaged cord or plug or after the

Fan malfunctions, has been dropped

or damaged in any manner. Return

Fan to authorized service facility for

examination, electrical or mechanical

adjustment or repair.

12. Do not insert or allow ngers or foreign

objects to enter any ventilation or

exhaust opening as it may cause an

electric shock or re, or damage the

Fan. Do not block or tamper with

the Fan in any manner while it is in

operation.

13.Locate the Power Cord so the Fan or

other objects are not resting on it. Do not

run Power Cord under carpeting or oor

mats. Do not cover Power Cord with

runners, or the like. Do not run Power

Cord through doorways, windows or

areas where cord impingement may

occur. Arrange Power Cord away from

room trafc and where it will not be

tripped over.

14.This Fan is not intended for use in

wet or damp locations. Never locate

a Fan where it may fall into water.

15. Do not use Fan outdoors.

16.This Fan is not suitable for use in

hazardous locations. Please refer to

National Electric Code (NEC) Article

500 or applicable state or local codes or

standards relating to electrical requirements

for Hazardous locations. THIS FAN DOES

NOT MEET THE REQUIREMENTS OF

NEC ARTICLE 500 (2008).

WARNING: REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK – DO NOT USE THIS FAN

WITH ANY SOLID STATE SPEED CONTROL

DEVICES.

CAUTION: BECAUSE OF THE SIZE AND

WEIGHT OF THIS FAN, MAKE SURE ALL

PARTS ARE COMPLETELY ASSEMBLED

ACCORDING TO INSTRUCTIONS. FAILURE

TO DO SO COULD RESULT IN FAN

COMING APART DURING OPERATION

AND/OR PERSONAL INJURY.

Operating Instructions & Parts Manual 99538/99539

New 5/11 5085459

GRILL AND BLADE ASSEMBLY

(Figures 3 and 4)

1. Install the Rear Grill onto the Motor, lin-

ing up the six holes in the grill with the

six threaded holes in the Motor. Install (6)

10-32 X 5/16" Hex Screws through the Rear

Grill into the Motor. Securely tighten all

(6) screws. (Figure 3)

2. Push the Fan Blade onto the Motor Shaft,

centering the Hub facing away from the

motor, until it stops against the shaft (Inset

A) . Align Square Head Bolt with at of

the Motor Shaft. TIGHTEN VERY SECURELY

WITH AN ADJUSTABLE WRENCH. Failure

to securely tighten the Bolt could result in

damage to the Fan and/or personal injury.

3. Hold the Front Grill so that the name, in the

center, is right side up and straight across.

Starting at the top: Fasten Front Grill to

Rear Grill by sliding the hooked wires on

the Front Grill over the outermost ring on

the Rear Grill. The (Figure 4 / Detail A).

bottom most hooks will require the use of a

athead screwdriver to complete assembly.

Stand behind the Fan. Slip the at of the

screwdriver between the Front and Rear

Grills, next to one of the unfastened hooks.

(Figure 4 / Detail B) Pull screwdriver handle

upwards towards the Rear Grill. Slip the

Front Grill hook over the Rear Grill outer

ring with a push. Repeat procedure with

remaining hooks.

CAUTION: DO NOT BEND WIRES ON

THE FRONT OR THE REAR GRILLS

Assembly

WALL BRACKET INSTALLATION

NOTE: Always install the bracket to a minimum of

2" x 4" studding.

1. Insert the 7/16-14 x 3-1/2" Bolt through Wall

Bracket and into the 7/16-14 Lock Nut. Tighten

with Adjustable Wrenches.

2. THE HARDWARE TO ATTACH THE WALL

BRACKET TO THE WALL STUD IS NOT SUPPLIED.

Locate the wall stud nearest to the desired Fan

location. Attach the Wall Bracket to the stud us-

ing (3) 5/16" diameter x 2" long Lag Screws.

3. Position the Motor Neck and align the Pivot Hole

with the Larger Hole in the Wall Bracket. (Figure 1)

4. " " "Insert the 1/2 X 1 Hex Bolt (3/4 head)

through the Motor Neck, and the Wall Bracket.

Place 1/2" diameter Split Lockwasher then the

1/2" diameter Hex Nut (3/4" head) and tighten

fully with 1” adjustable wrench.

5. From the same side of the Motor Neck, insert

one 1/4-20 X 1 5/8" Carriage Bolt through the

Arc-Shaped Slot in the Motor Neck and Hole

in the Wall Bracket.

To Fasten: Place one 1/4" Flatwasher, one 1/4" In-

ternal Tooth Lockwasher, a second 1/4" Flatwasher

and then tighten the Adjustable Knob over the

remaining threads. Final assembly of the Motor to

the Wall Mount Bracket is illustrated in .Figure 2

Figure 2

Final Assembly

of Motor to

Wall Mount

Bracket

Wall Mount Assembly

Figure 3

Inset A

Detail B

Bottom Hooks

Detail A

Top Hooks

Figure 4

Figure 1

Wall

Bracket

7/16-14 X 3 1/2"

Bolt

7/16-14 Lock Nut

P Clamp

Cable

Routing

Operating Instructions & Parts Manual 99538/99539

New 5/11 5085459

Specyfikacje produktu

Marka:	Air King
Kategoria:	Wentylator
Model:	99539

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Air King 99539, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Wentylator Air King

Air King E130SH Instrukcja

10 Października 2024

Air King AK100L Instrukcja

27 Września 2024

Air King 9071 Instrukcja

23 Września 2024

Air King 9145 Instrukcja

23 Września 2024

Air King 9723 Instrukcja

22 Września 2024

Air King 9312 Instrukcja

21 Września 2024

Air King 9018 Instrukcja

15 Września 2024

Air King AKLC703 Instrukcja

13 Września 2024

Air King 9130 Instrukcja

13 Września 2024

Air King 9170 Instrukcja

13 Września 2024

Instrukcje Wentylator

Najnowsze instrukcje dla Wentylator

Ausclimate EcoSmart ACAC300CB Instrukcja

14 Stycznia 2025

Breville the PopFan LFA100 Instrukcja

14 Stycznia 2025

Breville the AirDynamic 3D Connect LPF308 Instrukcja

14 Stycznia 2025

Ausclimate EcoSmart ACAC230CB Instrukcja

14 Stycznia 2025

Emerio FN-108784.1 Instrukcja

13 Stycznia 2025

Emerio FN-114204.1 Instrukcja

13 Stycznia 2025

Emerio FN-110475 Instrukcja

13 Stycznia 2025

Emerio FN-110139.3 Instrukcja

13 Stycznia 2025

Emerio FN-110477.2 Instrukcja

13 Stycznia 2025

Emerio FN-114223.3 Instrukcja

13 Stycznia 2025